45211
5
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
1*
2*
3*
4*5*
1 This product
2 Antenna jack
3 Fuse (10 A)
4 Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
5 Connect leads of the same
color to each other.
6 Cap (1*)
Do not remove cap if this
terminal is not in use.
7 Yellow (3*)
Back-up
(or accessory)
8 Yellow (2*)
Connect to the constant 12 V supply
terminal.
9 Red (5*)
Accessory
(or back-up)
10 Red (4*)
Connect to terminal controlled by
ignition switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
13 Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left
Green/black: Rear left
Violet: Rear right
Violet/black: Rear right
<YRD5142-A/S>6
Connections
En
<YRD5142-A/S> 17
Fig. 1
Abb. 1
Afb. 1
Рис. 1
14 Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
17 Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
18 Blue/white (6*)
The pin position of the ISO connector will differ depends
on the type of vehicle. Connect 6* and 7* when Pin 5 is
an antenna control type. In another type of vehicle, never
connect 6* and 7*.
<YRD5142-A/S>7
Connections
En
<YRD5142-A/S> 18
Important
! When this unit is installed in a vehicle without
ACC (accessory) position on the ignition
switch, red cable must be wired to the term-
inal that can detect the operation of the igni-
tion key. Otherwise, battery drain may result.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
! Use of this unit in conditions other than the
following could result in fire or malfunction.
Vehicles with a 12-volt battery and negative
grounding.
Speakers with 50 W (output value) and 4
ohm to 8 ohm (impedance value).
! To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions
below.
Disconnect the negative terminal of the
battery before installation.
Secure the wiring with cable clamps or ad-
hesive tape. To protect the wiring, wrap ad-
hesive tape around them where they lie
against metal parts.
Place all cables away from moving parts,
such as gear shift and seat rails.
Place all cables away from hot places,
such as near the heater outlet.
Do not pass the yellow cable through a
hole into the engine compartment to con-
nect to a battery.
Cover any disconnected cable connectors
with insulating tape.
Do not shorten any cables.
Never cut the insulation of the power cable
of this unit in order to share the power
with other devices. Current capacity of the
cable is limited.
Use a fuse of the rating prescribed.
Never wire the speaker negative cable di-
rectly to ground.
Never band together multiple speakers ne-
gative cables.
! Control signal is output through blue/white
cable when this unit is powered on. Connect it
to an external power amps system remote
control or the vehicles auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
vehicle is equipped with a glass antenna, con-
nect it to the antenna booster power supply
terminal.
! Never connect blue/white cable to external
power amps power terminal. Also, never con-
nect it to the power terminal of the auto anten-
na. Otherwise, battery drain or malfunction
may result.
! Black cable is ground. This cable and other
products ground cable (especially, high-cur-
rent products such as power amp) must be
wired separately. Otherwise, fire or malfunc-
tion may result if they are accidentally de-
tached.
Connection Diagram (Fig. 1)
1 This product
2 Antenna jack
3 Fuse (10 A)
4 Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
5 Connect leads of the same color to each
other.
6 Cap (1*)
Do not remove cap if this terminal is not in
use.
7 Yellow (3*)
Back-up (or accessory)
8 Yellow (2*)
Connect to the constant 12 V supply terminal.
9 Red (5*)
Accessory (or back-up)
<YRD5142-A/S>8
Connections
En
<YRD5142-A/S> 19
10 Red (4*)
Connect to terminal controlled by ignition
switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.
13 Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left +
Green/black: Rear left *
Violet: Rear right +
Violet/black: Rear right *
14 Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
17 Blue/white (7*)
Connect to auto-antenna relay control term-
inal (max. 300 mA 12 V DC).
18 Blue/white (6*)
The pin position of the ISO connector will dif-
fer depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
<YRD5142-A/S>9
Connections
En
<YRD5142-A/S> 20
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer DEH-2000MP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer DEH-2000MP

Pioneer DEH-2000MP Bedienungsanleitung - Deutsch, Englisch - 75 seiten

Pioneer DEH-2000MP Bedienungsanleitung - Holländisch - 60 seiten

Pioneer DEH-2000MP Bedienungsanleitung - Französisch - 75 seiten

Pioneer DEH-2000MP Bedienungsanleitung - Italienisch - 60 seiten

Pioneer DEH-2000MP Bedienungsanleitung - Spanisch - 75 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info