Bedienungsanleitung Pioneer DEH-2900MPB (Seite 5 von 8) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

6634

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Note:

• When this unit is installed in a vehicle without

ACC (accessory) position on the ignition switch,

red cable must be wired to the terminal that can

detect the operation of the ignition key.

Otherwise, battery drain may result.

• Use this unit in other than the following condi-

tions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunc-

tion, be sure to follow the directions below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhe-

sive tape around them where they lie against

metal parts.

— Place all cables away from moving parts,

such as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s nega-

tive cables.

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an

external power amp’s system remote control or

the vehicle’s auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is

equipped with a glass antenna, connect it to the

antenna booster power supply terminal.

• Never connect blue/white cable to external power

amp’s power terminal. Also, never connect it to

the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

• Black cable is ground. This cable and other prod-

uct’s ground cable (especially, high-current prod-

ucts such as power amp) must be wired separate-

ly. Otherwise, fire or malfunction may result if

they are accidentally detached.

• Cord function may differ according to the

product, even if cord color is the same. When

connecting this system, be sure to check all

manuals and connect cords correctly.

No ACC positionACC position

Connecting the Units

27. Yellow/black

If you use an equipment with Mute function, wire

this lead to the Audio Mute lead on that equipment.

If not, keep the Audio Mute lead free of any connections.

8. Cap (1*)

Do not remove cap if this

terminal is not in use.

14. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to

connect to both connectors.

10.Yellow (2*)

Connect to the constant

12 V supply terminal.

12. Red (4*)

Connect to terminal controlled

by ignition switch (12 V DC).

9. Yellow (3*)

Back-up

(or accessory)

11. Red (5*)

Accessory

(or back-up)

7. Connect leads of the same

color to each other.

18. Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

20. Blue/white (7*)

Connect to Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

Note:

Depending on the kind of vehicle, the function

of 3* and 5* may be different. In this case, be

sure to connect 2* to 5* and 4* to 3*.

2. This Product

3. Antenna jack

16. Connect with RCA cables

(sold separately)

21. Blue/white (6*)

22. The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control type. In another

type of vehicle, never connect 6* and 7*.

1. Rear output

13. Black (chassis ground)

Connect to a clean, paint-free

metal location.

26.

23. Left 24. Right

25. Rear Speaker 25. Rear Speaker

17. Power amp

(sold separately)

19. System remote control

Perform these connections when using

the optional amplifier.

5. Wired remote input

Hard-wired remote control adaptor can be

connected (sold separately).

4. Fuse (10 A)

15. Speaker leads

White: Front left

White/black: Front left

Gray: Front right

Gray/black: Front right

Green: Rear left

Green/black: Rear left

Violet: Rear right

Violet/black: Rear right

Connecting the Units ENGLISH

Connection Diagram

1. Rear output

2. This product

3. Antenna jack

4. Fuse (10 A)

5. Wired remote input

Hard-wired remote control adaptor can be con-

nected (sold separately).

6. Note:

Depending on the kind of vehicle, the function of

3* and 5* may be different. In this case, be sure

to connect 2* to 5* and 4* to 3*.

7. Connect leads of the same color to each other.

8. Cap (1*)

Do not remove cap if this terminal is not in use.

9. Yellow (3*)

Back-up (or accessory)

10. Yellow (2*)

Connect to the constant 12 V supply terminal.

11. Red (5*)

Accessory (or back-up)

12. Red (4*)

Connect to terminal controlled by ignition swich

(12 V DC).

13. Black (chassis ground)

Connect to a clean, paint-free metal location.

14. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to connect

to both connectors.

15. Speaker leads

White: Front left +

White/black: Front left ≠

Gray: Front right +

Gray/black: Front right ≠

Green: Rear left +

Green/black: Rear left ≠

Violet: Rear right +

Violet/black: Rear right ≠

16. Connect with RCA cables (sold separately)

17. Power amp (sold separately)

18. Blue/white

Connect to system control terminal of the power

amp (max. 300 mA 12 V DC).

19. System remote control

20. Blue/white (7*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

21. Blue/white (6*)

22.The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and

7* when Pin 5 is an antenna control type. In

another type of vehicle, never connect 6* and 7*.

23. Left

24. Right

25. Rear Speaker

26. Perform these connections when using the

optional amplifier.

27. Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead free

of any connections.

Pioneer DEH-2900MPB Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer DEH-2900MPB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info