Bedienungsanleitung Pioneer GM-4000F (Seite 4 von 8) (Englisch, Französisch)

60551

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Specifications

Installation

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

Current consumption ........................................................................................................ 18.1 A (at continuous power, 4 Ω)

Average current drawn* .......................................................................................................... 6.6 A (4 Ω for four channels)

9.0 A (4 Ω for two channels)

Fuse .................................................................................................................................................................................. 25 A

Dimensions ........................................................................................................................ 300 (W) × 61 (H) × 237 (D) mm

[12 (W) × 2-3/8 (H) × 9-3/8 (D) in]

Weight ........................................................................................................ 3.8 kg (8.4 lbs) (Leads for wiring not included)

Maximum power output ...................................................................................................................... 70 W × 4 / 150 W × 2

Continuous power output .......................................................... 35 W × 4 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.08% THD)

70 W × 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.8% THD)

40 W × 4 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.8% THD)

Load impedance ............................................................................................................................ 4 Ω (2 — 8 Ω allowable)

(Bridge connection: 4 — 8 Ω allowable)

Frequency response ............................................................................................................ 10 — 50,000 Hz (+0 dB, –1 dB)

Signal-to-noise ratio ...................................................................................................................... 100 dB (IHF–A network)

Distortion ............................................................................................................................................ 0.008% (10 W, 1 kHz)

Separation ........................................................................................................................................................ 60 dB (1 kHz)

Low pass filter ................................................................................................................................ Cut off frequency: 80 Hz

Cut off slope: –12 dB/oct

High pass filter ................................................................................................................................ Cut off frequency: 80 Hz

Cut off slope: –12 dB/oct

Maximum input level/impedance .................................................................................... RCA: 6.5 V/22 kΩ (0.4 — 6.5 V)

Speaker: 26 V/40 kΩ (1.6 — 26 V)

Note:

•Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

•The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.

CAUTION

• Do not install in:

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s

seat.

•Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-cir-

cuit.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

from damage.

• Install tapping screws in such a way that the

screw tip does not touch any wire. This is impor-

tant to prevent wires from being cut by vibration

of the car, which can result in fire.

•To prevent electric shock, do not install the ampli-

fier in places where it might come in contact with

liquids.

•To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

CAUTION:

To prevent malfunction and/or injury

•To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• Do not install the amplifier near a door where it

may get wet.

• Do not install the amplifier on unstable places

such as the spare tire board.

•The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

•Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

Example of installation on the floor

mat or on the chassis

1. Place the amplifier where it is to be

installed. Insert the supplied tapping

screws (4 × 18 mm) into the screw

holes. Push on the screws with a

screwdriver so they make marks

where the installation holes are to be

located.

2. Drill 2.5 mm (1/8 inch) diameter

holes at the point marked, and

install the amplifier, either on the

carpet or directly to the chassis.

Drill a 2.5 mm (1/8 inch)

diameter hole

Tapping-screws

(4 × 18 mm)

Floor mat

or chassis

HRD0267A_Eng 1/21/04 20:06 Page 13

Pioneer GM-4000F Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer GM-4000F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info