Bedienungsanleitung Pioneer PD-30-K (Seite 5 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

491903

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Connecting up 02

English

DeutschFrançais

Nederlands

Italiano Español Русский

Chapter 2:

Connecting up

Caution

• Before making or changing the connections,

switch off the power and disconnect the power cord

from the AC outlet.

• Connect the power cord after all the connections

between devices have been completed.

Analog audio output connections

By connecting this unit’s analog audio output to the

analog audio input of an amplifier, you can use the

amplifier to enjoy analog audio produced from this unit.

Digital audio output connections

If desired, the digital audio output from this unit can be

connected to an AV amplifier or digital recording device

(CD recorder, MD, etc.).

• This unit’s DIGITAL OUT terminals do not output

sound from SACD and DSD discs, nor from iPod/

iPhone/iPad devices.

Important

Care in the handling of optical fiber cables

• Do not allow optical fiber cables to be bent at sharp

angles. When storing optical fiber cables, roll in

coils of at least 15 cm diameter.

• When connecting optical fiber cables, align the

connectors correctly and insert fully. If the

orientation of the cable connector is incorrect and

excessive force is applied in the attempt to fasten

the connector, the connector may be deformed,

preventing the shutter from closing when the cable

is removed.

Note

• For digital audio output, CDs played on this unit

must produce linear PCM signals with a sampling

rate up to 44.1 kHz and quantitative bits up to 16

bits (some discs may not be playable depending on

the connected component and environment). For

information about other files, see page 12.

ANALOG

AUDIO INPUT

Amplifier

Audio cable (included)

PD-30’s rear panel

DIGITAL IN

OPTICAL

DIGITAL IN

COAXIAL

AV amplifier or

digital recording

device

Optical fiber cable

(commercially

available)

Coaxial digital

audio cable

(commercially

available)

PD-30’s rear panel

AV amplifier or

digital recording

device

Using centralized control with other

Pioneer components (PD-30 only)

This unit and other Pioneer components equipped with

CONTROL IN/OUT jacks can be controlled with a single

remote control by aiming the remote toward the signal

receptor on the AV amplifier or other component. This

also allows remote control of components not equipped

with a remote sensor, or installed in places where the

component’s remote sensor cannot be accessed.

Note

• For connections use a commercially available

monaural miniplug cord (without resistor).

• When connecting the CONTROL IN/OUT jacks,

commercially available audio cords must also be

used to make analog connections. Merely

connecting the CONTROL IN/OUT jacks alone will

not allow proper system control.

• When a control cord is connected to the PD-30’s

CONTROL IN jack, the unit cannot be controlled by

pointing the remote control at the PD-30 (the

remote sensor is automatically disabled).

Plugging in

Important

• If it is necessary to detach the power cord, first be

sure to press the 

STANDBY/ON button on the

front panel of the unit so the PD-30 is turned OFF or

the PD-10 is in standby mode before detaching the

cord.

• Confirm that the [-OFF-] indicator is not lighted in

the main unit’s front panel display before

disconnecting the power cord. If the power cord is

disconnected while the [-OFF-] indicator is still

lighted, the unit’s settings may revert to factory

defaults.

• When going on a trip or otherwise not using the

unit for an extended period, always disconnect the

power cord from its outlet.

Caution

• Do not use any power cord other than the one

supplied with this unit.

• Do not use the supplied power cord for any purpose

other than that described below.

After you’ve finished making all connections, plug the

unit into an AC outlet.

1 Plug the supplied power cord into the

AC IN

socket on the rear of the unit.

2 Plug the other end into AC outlet.

To other Pioneer

component equipped

with CONTROL IN jack

Remote control for

AV amplifier, etc.

Point the remote

control toward the

signal receiver on

the AV amplifier, etc.

Other Pioneer component

equipped with CONTROL

IN/OUT jacks

PD-30

To AC outlet

Power cord

PD-30’s rear panel

PD-30_PWSYXZT8.book 5 ページ２０１２年５月７日　月曜日　午前１１時３３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer PD-30-K Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer PD-30-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info