Bedienungsanleitung Pioneer S-L8 (Seite 45 von 48) (Englisch)

572156

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

9 Additional Information

Symptom

Playback sound is

muddy or distorted;

high frequency sounds

are excessively

emphasized.

Timer doesn’t operate.

Remote control unit

doesn’t work.

Power won’t turn on to

the deck or CD receiver.

Remote Locator

function doesn’t work

Likely cause

• The Dolby NR setting is not the same as that

used during recording.

• Clock isn’t set to the correct current time.

• Power interruption has caused the clock to be set

to the incorrect time (when the clock display is

flashing).

• Batteries are exhausted.

• A fluorescent lamp is located close to the remote

control unit.

• The remote control unit is not pointed at the

signal receiver on the display unit.

• System cable connection is incorrect.

• The microphone in the remote control is covered

• The remote control is too far away.

• The battery in the remote control is dead.

• The slide switch is in the OFF position.

• The interval between claps is too long or too

short.

Remedy

• Set the Dolby NR system to the same setting as

that used during recording (see p.22).

• Reset the clock to the correct current time

(see p.16).

• Reset the clock to the correct current time

(see p.16).

• Load new batteries.

• Remove the fluorescent lamp from the area of

the remote control unit.

• Point the remote control unit at the remote

sensor (located on the right side of the display

unit) when operating.

• Connect the system cable correctly.

• This is not a malfunction.

• Move to a different location and try again.

• Replace the battery.

• Slide the Remote Locator switch to the ON

position

• The interval should be about a second.

• When the system is installed near a television set, magnetic influence from the speakers may cause the television’s picture to be

distorted. This symptom frequently occurs when using an indoor antenna; in this event, install an outdoor antenna, or separate

the system farther from the television.

• Static electricity and other outside electrical influences may cause the system to operate incorrectly. In such cases, unplugging

and reconnecting the power cord may help correct the problem.

• More than one of the same kind of component (CD receiver, MD recorder, or cassette deck) cannot be connected at the same

time.

NOTE

Setting the tuner’s frequency interval:

FM broadcasts are normally tuned at 50kHz intervals and AM broadcasts at 9kHz intervals, but this setting can be changed to

100kHz (FM) and 10kHz (AM) if desired in the following way:

1. Switch the unit into standby mode.

2. Press

MENU and choose TUNER F. STEP using the $ or › button. Press SET to select it.

3. Switch between

AM 9K (FM 50K) and AM 10 K (FM 100 K) using the $ and › buttons. Press SET to select.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer S-L8 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info