612929
4
Zoom out
Zoom in
Vorherige Seite
1/26
Nächste Seite
4
1 Preparations
1.1 Confirm the products
The operations necessary to install the Pedaling Monitor System on the customer’s bicycle depend on which System it
is; SGY-PM910HL/HR or SGY-PM910H2, and on which cycle computer is being used; SGX-CA500, SGX-CA900, or
some other manufacturer’s product.
1.2 Outline of procedure
1.2.1 For the SGY-PM910HL/HR with an ANT+ cycle computer
Single Power Meter Mode:(SGY-PM910Hl/HR Factory Default Mode)
1. [3.1Temporarily affix the Magnet]: Attach the magnet to the frame temporarily.
2. [2.2.1.3 Check the Current Mode]: Remove then replace the magnet, and observe the LED. It should flash
Orange for ten seconds
3. [3.2 Magnet Detection]: Confirm that the magnet can be detected.
Within five minutes of replacing the battery, rotate the crank and confirm that the LED flashes when passing the
magnet.
4. [3.3.3 Fixing the Magnet]: Fix the magnet in place.
5. [4 Pairing with the Cyclocomputer]: Pair the sensor with the cycle computer.
6. [5 Zero Calibration]: Carry out Zero Calibration.
1.2.2 For the SGY-910H2/(HL+HR) with an ANT+ cycle computer
Dual Power Meter Mode:(SGY-PM910H2 Mode on shipment from Installation center)
1. [3.1Temporarily affix the Magnet]: Attach the left and right magnets to the frame temporarily.
2. [2.2.1.3 Check the Current Mode]: Remove then replace the magnet, and observe the LED. It should light
Orange for ten seconds.
3. [2.2 Mode Switching]: If the LED flashed in step 2, it is necessary to switch the mode to Dual Power Meter
Mode.
Push the button on the right side transmitter for two seconds, and the LED will flash quickly in Orange for ten
seconds. While this is happening, release the button and press it again for two seconds. The LED will then light in
Orange for ten seconds.
4. [3.2.2Detecting the Magnet Position]: Confirm that the magnet can be detected.
Within five minutes of replacing the battery, rotate the crank and confirm that the LED flashes when passing the magnet.
5. [3.3.3Fixing the Magnets]: Fix the magnet in place.
6. [4Pairing with the Cyclocomputer]: Pair the sensors with the cycle computer using the device number of the
right side sensor.
7. [5Zero Calibration]: Carry out Zero Calibration.
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer SGY-PM910H2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer SGY-PM910H2

Pioneer SGY-PM910H2 Bedienungsanleitung - Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch - 234 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info