574202

Pioneer VSX-C301-S Seite 38

38
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
Additional information
11
38
En
No sound from subwoofer. • The subwoofer is disconnected or switched
off.
• Connect or switch on the subwoofer (see page 13).
• The subwoofer's settings are incorrect. • Set the subwoofer (see page 29).
• Set the front speakers to Small (
S
) (see page 29).
• The subwoofer's levels are too low. • See
Setting individual channel levels
on page 31 to check
the speaker levels.
• The LFE Attenuator is set to
OFF
.• Set the LFE Attenuator to either
0 dB
or
10 dB
(see
page 30).
Noise is output when scanning a
DTS CD.
• The scan function performed by the player
slightly alters the digital information, making
it unreadable.
• This is not a malfunction, but be sure to turn the volume
down to prevent the output of loud noise from your
speakers.
The Dolby/DTS indicator doesn't
light when playing Dolby/DTS
software.
• The player is paused. • Press play.
• The player's sound output settings are
wrong.
• Set the player correctly (consult the manual that came
with the player, if necessary).
When playing a 96 kHz/24bit disc
the sound is too loud.
• Different discs have different recording
levels so some may be louder than others.
• Turn the volume down.
The sound distorts. • The analog signal is too strong. • Turn on input attenuator (see page 30).
• Master volume is too loud. • Turn the volume down.
You can only hear treble from
speakers.
• The front speakers are set to small (
S
). • Set the front speakers to large (
L
) (see page 29).
Sound is produced from analog
components, but not from digital
ones (DVD, LD, CD-ROM etc.).
• Digital connections are incorrect. • Make digital connections (see page 8)
• The digital output of the player is turned off. • Turn on the digital output of the player on (consult the
manual that came with the player, if necessary).
• The CD-ROM player is outputting a data
stream (not an audio signal) which is
incompatible with this receiver.
• Use a player that is compatible with this receiver.
• Analog input has been selected. • Select digital input (see page 27).
• The digital input assignment is wrong. • Assign the digital input (see page 30).
No sound is output or a noise is
output when Dolby Digital/DTS
software is played back.
• A DVD player not compatible with Dolby
Digital/DTS is being used.
• Make sure your DVD player is compatible with Dolby
Digital/DTS.
• The settings on the DVD player are incorrect
and/or the DTS signal output is turned off.
• Make sure the player's settings are correct and/or the
DTS signal out is on. Refer to the instruction manual
supplied with the DVD player.
• The digital output level is turned down on a
CD player or other component equipped with
digital output level adjustment capability. (The
DTS signal has been altered by the player, and
cannot be read.)
• Set the digital volume level of the player to full, or to the
neutral position.
The settings have all been
cleared.
• The receiver has been unplugged or the
main power turned off for more than a month.
• Set the receiver again (see page 29).
No image is output when an
input is selected.
• The video connections are incorrect. • Make sure the video component is connected correctly
(see page 12).
• The input source is not properly selected. • Make sure the proper component is selected by
pressing the correct function button (see page 22).
• The DVD/video player settings are incorrect. • Set correctly. Refer to the instruction manual supplied
with the DVD/video player.
OVERLOAD
blinks in the display
and the power turns off
automatically.
• The speaker cable is shorting out the unit. • Make sure there are no loose strands of speaker wire
touching the metal casing of the receiver.
• The output is too high. • Turn the volume down.
You can't set the subwoofer
frequency crossover.
• All the speakers are set to either large (
L
) or
––
(i.e. no speakers are set to small).
• Change the speaker settings (see page 29).
The display is dark or off. • The display is set to dark or off. • Press
DIMMER
on the remote control repeatedly to
select a different brightness.
After making an adjustment the
display goes off.
• The display is set to off. • Press
DIMMER
on the remote control repeatedly to
select a different brightness.
Symptom
Cause Remedy
vsx-c301_FL.book 38 ページ ２００３年４月１１日　金曜日　午後１１時３３分
… 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer VSX-C301-S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info