Bedienungsanleitung Polar PFL 1000 (Seite 2 von 2) (Englisch)

632185

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 801 10027

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 5.0 49* 1.90 2:00

Cotton 60 5.0 49 1.05 2:10

Cotton with “Eco”** 60 5.0 49 0.95 2:20

Cotton 40 5.0 49 0.60 2:00

Synthetics 60 2.5 50* 0.70 1:30

Synthetics 40 2.5 45 0.55 1:15

Delicates 30 1.5 50 0.50 0:45

Daily load 40 3.0 45 0.45 1:00

Quick wash 30 3.0 40 0.40 0:30

Wool 40 1.0 55 0.60 0:45

Handwash 40 1.0 45 0.60 0:40

Add detergents as indicated on the front page and as

described in the chapter “Detergent and Additives” in

your Instructions for Use. Close the door and turn the

programme selector to the desired programme and

temperature. The indication lamp next to the “Start/

Pause” button flashes.

CONSUMPTION DATA

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the

home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type

of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water

out.

** Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR AND

SELECT THE PROGRAMME

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the door can be opened. As long

as a wash programme is running, the door remains

locked and must on no account be forced open.

In case you have an urgent need to open it during a

running programme, refer to “Cancel (Reset) a running

programme before the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”;

if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned: in the

latter case refer to the Instructions for Use (“Removing

the Filter”).

“Intensive rinse” button

• More water is added and rinse cycle is prologned.

• This option is particularly suitable for areas with very

soft water, washing baby linen and helps people

with allergies.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• This option is particularly recommended for the

programmes “Synthetics”, “Daily load” and

“Delicates”.

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain only.

Note: The programme stops to “Rinse hold” at the

time the “Anticrease” light in the programme

sequence indicator is on. The indication lamp next

to the “Start/Pause” button flashes.

• If you select “Rinse Hold” do not leave items to soak

for too long.

Terminate the “Rinse hold” option:

• Press the “Start/Pause” button; the programme

will terminate automatically with the final spin cycle

for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain”

programme and press the “Start/Pause” button.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows

the current programme phase, running from left to right

through Wash, Rinse, Spin/Drain.

When the programme phrase is finised, the

corresponding indication goes out.

PROGRAMME END

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme (with temperature), any

options and another spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before the

end.

• Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the door

can be opened.

SELECT ANY DESIRED OPTION

Push the button(s) of any option(s) desired - the

respective indication lamp lights up.

When the combination of programme and additional

option(s) is not possible, the indication lights switch off

automatically. Unsuitable combinations of options are

deselected automatically.

“Eco” button

• With a modified temperature profile and a slightly

prologned washing duration, the optimum

combination of excellent washing result and even

lower energy consumption is achieved.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time by

approximately 15 min.

• Do not use liquid detergent for the main wash when

activating the Prewash option.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain during

the rinse. The water is drained out only.

START DELAY

The “Start delay” allows to run the machine at the

consumer's convenience, for example at night when

electricity is cheaper.

• Select programme, temperature and options.

• Press the “Start delay” button to select the delay

time by 1, 3, 6, 9 or 12 hours.

• Press the “Start/Pause” button.

The indication next to the “Start delay” button lights

up and goes off when the programme starts.

• Once having pressed the “Start/Pause” button,

the countdown of the time delay begins. When the

programme starts, the start delay indicator light

goes off and is replaced by the programme sequence

indication.

• After the “Start/Pause” button has been pressed,

the number of hours preselected can be reduced by

pressing again the “Start delay” button.

• Do not use liquid detergent when activating the

Start delay.

To cancel the “Start delay”

..before you press the “Start/Pause” button:

• Turn the programme selector to another position

or press the “Reset” button.

..after having pressed the “Start/Pause” button:

• Press the “Reset” button for at least 3 second - the

start delay indicator light goes out.

Polar PFL 1000 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polar PFL 1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info