Bedienungsanleitung Powerplus pow xq 5315 (Seite 6 von 10) (Englisch)

383783

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

POWXQ5315 EN

 Never block the saw blade guard. Repair a jammed saw blade guard before using the

machine again.

 Replace a broken tension spring before using the machine again.

 Do not use saw blades made of HSS steel.

 Do not use bent, deformed or otherwise damaged saw blades.

 Do not use saw blades which do not meet the specifications stated in this manual.

 Before sawing, remove all nails and other metal objects from the workpiece.

 Never start sawing before the saw reaches its full speed.

 Securely clamp the workpiece. Never attempt to saw extremely small workpieces.

 Only put the machine aside after switching off and when the saw blade has come to a

complete standstill.

 Never try to slow the saw blade down by exerting pressure on the side.

 Before performing maintenance to the machine, always unplug the machine.

7 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS

Warning! The laser beam potentially causes eye damage. Do not look or

stare into the laser beam.

 During use, do not point the laser beam at people, directly or indirectly through reflecting

surfaces.

 This laser complies with class 2 according to the relevant standard. The unit includes no

servicing components. Do not open the housing for any reason. If the unit is damaged,

have the damage repaired by an authorized repair agent.

 Laser viewing glasses are not protective glasses against laser radiation.

8 ADJUSTMENTS

8.1 Replacing the saw blade (15)

Only use sharp and undamaged saw blades. Cracked or bent saw blades

must be replaced immediately.

Before performing any adjustments disconnect the plug.

 Place the saw on a side of a flat surface.

 Place the 2-pin wrench provided in the slots of the outer flange (16).

 Firmly keep the 2-pin wrench in place while you unscrew the blade clamp screw (17) by

inner hexagon wrench provided.

 Remove the blade clamp screw (17), outer flange (16), and washer.

 Lift the lower guard (18) by using the lower guard lever (14) and remove the blade.

 Clean the saw blade flanges, and then mount the new saw blade onto the spindle, which

is against the inner flange.

 Make sure the saw teeth and arrow on the blade is to the same direction as the arrow on

the upper guard.

 Reinstall the outer flange(16), washer and tighten the blade clamp screw (17).

 Make sure the saw blade can runs freely by turning the blade by hand.

8.2 Adjusting the depth of cut

The depth of the cut is infinitely adjustable.

A clean cut is achieved with the saw blade protruding from the material by approx. 3 mm.

 Loosen the lock lever for depth adjustment (19).

 Set the required depth of cut according to the scale.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus pow xq 5315 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus pow xq 5315

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info