Bedienungsanleitung Powerplus pow xq5234 (Seite 9 von 13) (Englisch)

389143

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

POWXQ5234 EN

9.4 Installing/removing bits

9.4.1 Installing bits

Lock the switch trigger by placing the direction of rotation selector in centre position.

Open or close chuck jaws to a point where the opening is slightly larger than the bit size

you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of

the chuck jaws. Insert drill bit straight into chuck the full length of the jaws as shown in.

Tighten the chuck jaws on the drill bit.

WARNING:

Make sure to insert drill bit straight into chuck jaws.

Do not insert drill bit into chuck jaws at an angle, this could cause drill bit to be thrown from

drill resulting in possible serious personal injury or damage to the chuck.

9.4.2 Removing bits

Lock the switch trigger by placing rotation selector in centre position.

Loosen the chuck jaws from the drill bit.

Do not use a wrench to tighten or loosen the chuck jaws.

Remove the drill bit from the chuck jaws.

9.5 Adjustable torque

This drill is equipped with an adjustable torque for driving different types of screws into

different materials. The proper setting depends on the type of material and the size of

screw you are using.

TO ADJUST TORQUE: Identify the 25 position torque ring located on the front of the drill.

Rotate adjusting ring (2) to the desired setting.

1-5

For driving small screws

6-10

For driving screws into soft material

11-15

For driving screws into soft and hard materials

16-20

For driving screws in hard wood

21-25

(

)

For heavy drilling

For hammer drilling

10 DRILLING

10.1 Drilling hard smooth surfaces

When drilling hard smooth surfaces use a centre punch to mark desired hole location. This

will prevent the drill bit from slipping off centre as the hole is started. However, the low

speed feature allows starting holes without centre punching if desired. To accomplish this,

simply operate the drill at a low speed until the hole is started. The material to be drilled

should be secured in a vise or with clamps to keep it from turning as the drill bit rotates.

Hold tool firmly and place the bit at the point to be drilled. Move the drill bit into the work

piece applying only enough pressure to keep the bit cutting. Do not force or apply side

pressure to elongate a hole.

WARNING:

Be prepared for binding or bit breakthrough. When these situations occur, drill has a

tendency to grab and kick opposite to the direction of rotation and could cause loss of

control when breaking through material. If not prepared, this loss of control can result in

possible serious injury. If the bit jams in work piece or the drill stalls, release switch trigger

immediately. Remove the bit from the work piece and determine the reason for jamming.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus pow xq5234 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus pow xq5234

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info