480993
5
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
POW4012 EN
Copyright © 2014 VARO P a g e | 5 www.varo.com
Always keep the holes in the base plate clean from dust.
Always connect a vacuum cleaner to the attached adaptor during your work.
Take special care when sanding lead based paint:
All persons entering the work area must wear a mask specially designed for protection
against lead paint dust and fumes.
Children and pregnant women must not enter the work area.
Do not eat, drink or smoke in the work area.
Do not leave the tool running. Operate the tool only when hand-held.
Ventilate your work area adequately when you perform sanding operations.
Be sure that there are no cracks or breakage on the pad before use. Cracks or breakage
may cause a personal injury.
7 OPERATION
Do not sand plaster surfaces, (WARNING: In this case your guarantee
becomes void) this may clog the motor (brushes, ball bearings, ..).
7.1 Switching on/off
To switch on the machine press the on/off switch.
To switch off the machine, release the on/off switch.
To switch the machine to continuous mode, you keep the on/off switch fully pressed and
simultaneously press the loch button. And subsequently release the on/off switch.
To switch off continuous mode, press the on/off switch again.
7.2 Attaching the sandpaper
Open the paper clamps.
Take sanding paper of the required grain size and place it on the sanding pad.
Make sure that the perforation in the paper corresponds with those on the sanding pad.
Fold tha sanding paper at both ends around the edges of the sanding pad.
Close the paper clamps one by one.
Make sure that the ends of the sanding paper are clamped.
The sanding paper must be fitted firmly on the sanding pad and should not come loose.
7.3 Collecting the dust
For a better dust extraction of the working surface, your sanding machine can be
connected to the ordinary vacuum cleaner for house-use.
Slide the suction mouth of a vacuum cleaner onto the connection.
The vacuum-cleaner connecting piece is supplied with the appliance.
8 TECHNICAL DATA
Power rating
135W
Mains voltage
230-240V
Frequency
50Hz
Sanding surface
90 X 187 mm
No load speed
12000 min-1
Weight
1.19kg
Safety class
II
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POW4012 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POW4012

Powerplus POW4012 Bedienungsanleitung - Deutsch - 8 seiten

Powerplus POW4012 Bedienungsanleitung - Holländisch - 7 seiten

Powerplus POW4012 Bedienungsanleitung - Französisch - 8 seiten

Powerplus POW4012 Zusatzinformation - Alle Sprachen - 1 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info