Bedienungsanleitung Powerplus POW751 (Seite 8 von 12) (Englisch)

481005

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POW751 EN

6.5 Spraying techniques (fig d.)

To obtain the best results, keep your spray gun level and parallel to the surface at all times.

Keep the nozzle 25 - 30 cm from the surface and spray evenly from side to side or up and

down. Do not spray at an angle as this will lead to paint runs on the surface. Use smooth and

even strokes. When spraying large areas, use a criss-cross pattern as shown.

Fig E.

Never start or stop the spray gun while it is aimed at the surface to be sprayed. Evenly control

the speed of movement of the spray gun. A fast speed of movement over the surface will give

a thin coat and a slow speed will give a heavy coat. Apply one coat at a time. If a further coat

is required, make sure you observe the manufacturers drying time recommendations before

applying a second coat. When spraying small areas, keep the output control on a low setting.

This will avoid using too much paint and prevent overspray. Where possible avoid stopping

and starting when spraying an object. This can lead to too much, or not enough paint being

applied. Do not tip the spray gun to more than 45 °C

6.6 Fitting and using the flexible nozzle (fig. F)

The flexible nozzle extension should be used to spray flat or horizontal surfaces. It should

also be used in areas with limited access. To fit the flexible nozzle, unscrew the basket nozzle

and attach the flexible nozzle in its place Replace the basket nozzle on the end of the flexible

nozzle and tighten.

7 CLEANING AND MAINTENANCE (FIG. G.)

Always remember to disconnect from the mains supply before cleaning the

spray gun or paint container.

It is essential that the spray gun is cleaned thoroughly after every use. Failure to clean it will

almost certainly result in blockages and it may not operate when you next come to use it! The

guarantee does not cover cleaning a sprayer that has not been properly cleaned by the user.

7.1 The following action must be taken after every use.

 Empty any remaining material from the container.

 Clean the container thoroughly with the thinner that was used.

 Pour some thinner into the container and spray through the spray gun until only clean

thinner is coming out of the nozzle.

 Thoroughly clean the paint pick up pipe and filter with thinner.

 Clean the basket and nozzle and remove any other debris or paint that remains.

 Turn the spray gun upside down and apply a few drops of light oil to the two apertures (F).

This will lubricate the piston and cylinder.

If your spray gun should require extra internal cleaning, it may be necessary to disassemble it.

If so the following actions should be taken.

 Remove the plug from the mains socket.

 Remove paint container, pick up pipe and filter.

 Undo the 4 screws (G).

 Take off the pump assembly.

 Release the nozzle (H), valve (J), piston (K) and spring (L)

 Clean the cylinder (M) and all parts thoroughly with solvent.

 Apply a few drops of light lubricating oil to the piston, spring and cylinder.

 Reassemble the spray gun.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POW751 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POW751

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info