Bedienungsanleitung Powerplus POWX0617 (Seite 6 von 10) (Englisch)

645227

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

POWX0617 EN

 Make sure that the workpiece is sufficiently supported or clamped. Keep your hands away

from the surface to be cut.

 Always wear safety goggles and hearing protection. If desired or required also use another

kind of protection like for example an apron or helmet.

 Ensure that mounted wheels and points are fitted in accordance with the manufacturer’s

instructions.

 Ensure that blotters are used when they are provided with the bonded abrasive product

and when they are required.

 If a guard is supplied with the tool never use the tool without such a guard.

 For tools intended to be fitted with threaded hole wheel, ensure that the thread in the

wheel is long enough to accept the spindle length.

 Ensure that ventilation openings are kept clear when working in dusty conditions. If it

should become necessary to clear dust, first disconnect the tool from the mains supply

(use non metallic objects) and avoid damaging internal parts.

 Though poor conditions of the electrical mains, shortly voltage drops can appear when

starting the equipment. This can influence other equipment (eq. blinking of a lamp). If the

mains-impedance Zmax <0.348 Ohm, such disturbances are not expected. (In case of

need, you may contact your local supply authority for further information.

7 OPERATION

7.1 Fitting the auxiliary handle (Fig. 1)

Ensure that the plug is not in the socket when fitting or removing the

auxiliary handle.

The auxiliary handle (7) can be attached to the angle grinder in three different positions: left,

on top and right.

7.2 Assembly the protective guard (Fig. 2 & 3)

1. Loosen the clip of the protective guard (8) by pulling lock lever of protective guard (1)

outward.

2. Turn the protective guard so that uncovered part of the disc is as far apart as possible from

the hand on main handle (4).

3. Fix the protection guard by pushing the lock lever inwards (the protective guard should no

longer be able to move).

NOTE: If the protective guard can not be fixed firmly by the lock lever (1), use a hexagon

wrench to tighten the hexagon nut. (See attached figure 3)

7.3 Replacing the grinding disc (Fig. 4 & 5)

Beware – a disc which has been used may be very hot!

 Pull out the power plug from the mains socket.

 Depress and hold down the spindle lock button (2) to secure the spindle.

 Turn the shaft until it locks.

 Remove the outer flange (a) and backing flange (b) by using the two-hole spanner

provided.

 Fit the desired disc (9) on the spindle and replace the outer flange and backing flange.

Release the spindle lock.

Important! Only ever press the spindle lock when the motor and grinding

spindle are at a standstill!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0617 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0617

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info