Bedienungsanleitung Powerplus POWX07551T (Seite 15 von 19) (Englisch)

675011

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

POWX07551T EN

 Grasp and pull the switch handle (4) forward until the center of the saw blade is over the

front of the workpiece (3).

 Engage the trigger to turn the saw on.

 When the saw reaches full speed, slowly push the switch handle down, cutting through the

leading edge of the workpiece.

 Slowly move the switch handle toward the fence, completing the cut.

 Release the trigger and allow the blade to stop spinning before raising the cutting head

and removing the workpiece.

9.7 Cutting bowed material (Fig. 27)

 A bowed workpiece must be positioned against the fence and secured with a clamp (1)

before cutting as shown. Do not position workpiece incorrectly or try to cut the workpiece

without the support of the fence. This will cause the blade to bind and could result in

personal injury.

9.8 Cutting grooves (Fig. 28)

WARNING: DO NOT USE A DADO BLADE, use only the standard saw blade

for this operation.

 Mark lines to identify the width and depth of the desired cut on the workpiece and put the

workpiece on the table and aim the inside tip of the blade at the line. Use a clamp to

secure the workpiece on the table.

 Lower the cutting head so the tip of the blade touches the top surface of the workpiece at

the marked line.

 While holding the upper arm in position, turn the stop knob (2) until it touches the stop

plate (1).

 Cut two parallel grooves as shown.

9.9 Auxiliary wood fence (Fig. 29)

When making multiple or repetitive cuts that result in cut-off pieces of one inch or less, it is

possible for the saw blade to catch the cut-off piece and throw it out of the saw or into the blade

guard and housing, possibly causing damage or injury. To minimize this, an auxiliary wood fence

(1) can be mounted to your saw. Holes are provided in the saw fence to attach an auxiliary wood

fence (this provides additional depth of cut). This fence should be constructed of straight auxiliary

wood approximately 3/4 in. thick by 1-1/2 in. high by 16 in. long. Attach the wood fence securely

and make a full depth cut to make a blade slot. Check for interference between the wood fence

and the lower blade guard. Adjust if necessary.

NOTE: This auxiliary fence is used only with the saw blade in the 0° bevel

position (90° to the table). The auxiliary wood fence must be removed when

bevel cutting.

10 CLEANING AND MAINTENANCE

ATTENTION! !Before performing any work on the equipment, pull the power

plug.

10.1 Cleaning

 Keep the ventilation slots of the machine clean to prevent overheating of the engine.

 Regularly clean the machine housing with a soft cloth, preferably after each use.

 Keep the ventilation slots free from dust and dirt.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX07551T Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX07551T

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info