795422
9
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
POWX075740DB EN
Copyright © 2022 VARO P a g e | 9 www.varo.com
Pull down on the saw head to check the current setting.
To change the setting, first loosen the knurled depth stop nut on the depth stop bolt. Turn
the depth stop bolt clockwise to decrease depth and counterclockwise to increase depth.
Tighten the depth stop nut after adjustment.
If needed, push the depth stop to the right to temporarily disable it.
9.9 Switching ON / OFF
For your safety use both hands to switch the power tool on and off.
Connect the power tool to the power supply.
To turn the machine on, simultaneously press the main switch (14) and locking button
(24).
When you want to turn off the machine, you have to release the on/off switch (14).
Important! Place the material you want to saw flat on the machine surface and secure with
the clamping device (11) so that the material cannot move while you are cutting.
After switching on the saw, wait for the blade (2) to reach its maximum speed.
Press the release lever (15) sideways and, using the handle (13), apply steady and light
downward pressure to move the machine head through the workpiece.
When the cut is completed, return the machine to its top parking position and let go of the
On/Off switch.
Caution! A return spring causes the machine head to rise automatically at the end of the cut.
Do not let go of the handle (13) as soon as the cut is completed but steady the machine head
and allow it to rise slowly.
9.10 Laser
You can switch the laser ON and OFF with the switch (29)
The laser (22) directs a beam onto the workpiece
Extremely precise cuts can be made using the laser function.
9.11 Dust bag
To attach the dust bag (18), fit it onto the dust extraction adapter. When the dust bag is about
half full, remove the dust bag from the tool and empty it.
9.12 Sawing
Make sure the saw blade doesn’t block while you are sawing. It causes
damage to and burning of the motor. If there is a blockade of the saw blade,
please loosen the switch immediately to prevent damage at the motor.
Clamp the work piece firmly.
Set the required horizontal mitre angle or the required vertical bevel angle.
Switch on the power tool.
Move the handle (13) slowly downwards.
For long workpieces you should use the slide; loosen the locking knob for this purpose.
Saw trough the work piece.
Switch off the power tool.
Wait until the saw blade (2) has come to a complete standstill before removing the work
piece.
9.13 Sawing special work pieces
Curved or round work pieces need to be secured against slipping.
Make sure there is no gap between the work piece and the fence (4) or the saw table (5).
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POWX075740DB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POWX075740DB

Powerplus POWX075740DB Bedienungsanleitung - Deutsch - 14 seiten

Powerplus POWX075740DB Bedienungsanleitung - Holländisch - 13 seiten

Powerplus POWX075740DB Bedienungsanleitung - Französisch - 14 seiten

Powerplus POWX075740DB Zusatzinformation - Alle Sprachen - 6 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info