Bedienungsanleitung Powerplus POWX0760 (Seite 20 von 23) (Englisch)

677891

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

POWX0760 EN

10.2.9 Carrying tool (Fig. 66)

Make sure that the tool is unplugged. For the tool just used in the Mitre saw mode, secure the

blade at 0° bevel angle and the turn table at 0° Mitre angle. Lower the handle fully and lock it

in the lowered position by fully pushing in the stopper pin.

Carry the tool by holding the tool part shown in the figure. (Fig. 67)

CAUTION:

 Always secure all moving portions before carrying the tool.

 Before carrying the tool, always set up the tool in the Mitre saw mode.

 Make sure that the lower blade guard C is installed on the tool.

11 MAINTENANCE

CAUTION:

 Always be sure that the tool is switched off and unplugged before attempting to perform

inspection or maintenance.

WARNING: Always be sure that the blade is sharp and clean for the best

and safest performance.

11.1 Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory, but rough handling may have affected

the alignment. If your tool is not aligned properly, perform the following:

11.1.1 Mitre angle

Mitre angle 0° adjusting bolts are located in four positions.

Loosen four Mitre angle 0° adjusting bolts by turning counterclockwise from the underside of

the table. (Fig. 68)

Lower the handle fully and lock it in the lowered position by pulling and rotating the stopper pin

to the angle of 90° clockwise. Square the side of the blade with the face of the guide fence

using a triangular rule, trysquare, etc. Then securely tighten the four adjusting bolts on the sub

arm from the underside of the table. Make sure that the pointer points to 0° on the Mitre scale.

If not so, adjust the pointer position by loosening the screw securing the pointer. After

adjusting it, securely tighten the screw. (Fig. 69)

11.1.2 Bevel angle

(1) 0° bevel angle

Lower the handle fully and lock it in the lowered position by pulling and rotating the stopper pin

to the angle of 90° clockwise. Loosen the lever at the rear of the tool.

Turn, from the underside of the table, the 0° bevel angle adjusting bolt on the right side of the

sub arm two or three revolutions counterclockwise to tilt the blade to the right. (Fig. 70)

Carefully square the side of the blade with the top surface of the turn table using the triangular

rule, try-square, etc. by turning the 0° bevel angle adjusting bolt clockwise. (Fig. 71)

Make sure that the pointer on the turn table point to 0° on the bevel scale on the arm. If it does

not point to 0°, loosen the screw which secures the pointer and adjust the pointer so that it will

point to 0°.

(2) 45° bevel angle Adjust the 45° bevel angle only after performing 0° bevel angle adjustment.

To adjust left 45° bevel angle, loosen the lever and tilt the blade to the left fully. Make sure that

the pointer on the arm points to 45° on the bevel scale on the arm. If the pointer does not point

to 45°, turn, from the underside of the table, the 45° bevel angle adjusting bolt on the left side

of the sub arm until the pointer points to 45°. (Fig. 72)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX0760 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX0760

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info