Bedienungsanleitung Powerplus POWX1370 (Seite 5 von 7) (Englisch)

676273

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

POWX1370 EN

7.1 Testing the sequential trip safety mechanism

 The nailer should not fire if the safety (3) is not depressed against the workpiece.

 Make sure the switch is turned off.

 Empty the magazine (5) of nails.

 Check that the trigger (6) and safety (3) of the tool, move freely, without sticking.

 Plug the tool into the power outlet.

 Test the tool by depressing the safety (3) of the tool against the workpiece without pulling

the trigger (6). The tool must not cycle (fire). If it cycles (fires), stop immediately and take

the tool to an qualified service technician for repair.

 Hold the tool away or off of the workpiece. The safety (3) of the tool should return to its

original position. Squeeze the trigger (6). The tool should not cycle (fire). If it cycles (fires),

stop immediately and take the tool to an authorized service technician.

 Depress the safety (3) of the tool against the workpiece and squeeze the trigger (6). The

tool must cycle (fire) once only. If it fails to cycle (fire) or fires more than once, take it to an

authorized service technician.

Warning! Disconnect the nailer from the power outlet whenever loading it.

7.2 Loading brad nails and staples. (Fig 2&3)

 Depress the lever (10) and extend the inner magazine (11) all the way out.

 When loading brad nails, make sure you insert the pins of the nails on the side of the

magazine (5) with the groove in it. The brad nails should fit into the groove. When loading

staples, insert them crown up, onto the magazine (5).

 Slide the extended inner magazine (11) back until the lever (10) clicks into place. Do not

force the inner magazine (11) or you may damage the tool.

When the unit is loaded with fasteners and you are ready to begin, plug the

nailer/stapler power cord (8) into a power outlet.

 Hold the tool with both hands, so that the nose (4) is flat against the workpiece, making

sure that the safety (3) is also firmly against the workpiece.

 Gently squeeze the trigger (6) to fire the tool.

Note: practice depth adjustment on scrap material first.

 If more depth is needed, and you are nailing or stapling into a hard surface, you may apply

pressure on the top of the unit. On soft surfaces do not apply excessive pressure or the

brad nail or staple may penetrate the workpiece too deeply.

Note: each time you fire the nailer / stapler, the safety (3) must be pressed

firmly against the workpiece.

7.3 Removing jammed staples or brad nails

 First, unplug the nailer / stapler. If a nail is jammed in the discharge area, simply remove it

with pliers.

 If a nail is jammed in the magazine (5), depress the lever (10) and extend the inner

magazine (11) all the way out, (Fig 2&3). Use a flat screwdriver an/or needle nose plier to

free the brad nail or staple.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX1370 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX1370

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info