Bedienungsanleitung Powerplus POWX1420 (Seite 6 von 9) (Englisch)

645073

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

POWX1420 EN

7.2 Depth adjustment (Fig. 7)

 Loosen the cutting depth setting clamp (9) by lifting the lock lever.

 Hold the base plate (14) flat against the body of the work piece and lift the body of the saw

until the blade is at the right depth.

 Tighten the depth locking lever.

7.3 Angle adjustment (Fig. 8)

 Loosen the lock lever knob for angle adjustment (11).

 Adjust the base plate (14)(to the desired angle between 0° to 45°.

 Tighten the lock lever knob for angle adjustment (11).

Note: for best cutting results, always ensure that saw blade protrudes no

more than 3 mm below the bottom surface of the workpiece.

7.4 General cut

 Mark a cutting line on the workpiece.

 Rest the front part of the shoe flat on the workpiece surface with the blade not making any

contact with the workpiece.

 Switch on the tool and allow it to reach its full speed.

 Align the saw blade with the cutting line on the workpiece, gently push the saw forward.

Never force the saw but maintain a light and continuous pressure when completing the

cut. Switch off the tool only after the tool is completely away from the workpiece When the

cutting is interrupted, resume the cut by allowing the blade to reach full speed and then re-

entering the cut slowly

 When cutting across the grain, the fibres of the wood will have a tendency to lift and tear,

moving the saw slowly to minimize this effect.

Note: there are two notches on the front edge of the shoe as an aid for

alignment. When making a 45° bevel cut, just align the left notch marked

with 45° with the cutting line on the workpiece. For a straight 90° cut, align

the right notch marked with 0° with the cutting line on the workpiece. For

precise cutting, always make a trial cut before carrying out operation

7.5 Pocket cutting

 Disconnect the plug from the power supply before making any adjustments. Set the depth

adjustment based on the thickness of the line drawing for the cut .raise the lower guard by

using the lift lever.

 With the blade barely above the material to be cut, start the saw and allow the blade to

come to full speed. Gradually lower the blade unto the material to be cut using the front

end of the shoe as a pivot point. When the blade starts cutting, release the lower guard.

When the shoe is resting flat on the surface being cut, proceed cutting in a forward

direction to the end of the cut. Allow the blade to come to a full stop before removing it

from the cut. Never pull the saw backward since the blade will climb out of the cut and

kickback will occur. Turn the saw around and finish the cut in a normal manner, sawing

forward. Use a jigsaw or a hand saw to finish the cut in the corners, if required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX1420 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX1420

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info