Bedienungsanleitung Powerplus POWX1425 (Seite 9 von 12) (Englisch)

645074

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWX1425 EN

 Once the cut has been finished, lift the tool from the work surface before switching off. If a

lot of dust has been created, keep switched on for a few seconds extra to allow the dust to

clear from within the tool.

WARNING! If any of the following events occur during normal operation, the

power supply should be shut off at once and tool thoroughly inspected by a

qualified person and repaired if necessary:

 The rotating parts get stuck or speed drops abnormally low.

 The tool shakes abnormally accompanied by some unusual noise.

 The motor housing gets abnormally hot.

 Heavy sparks occur around the motor area.

9.5 Pocket Cut

 Install a saw blade suitable for the material you are about to saw. (see chapter 2.

Description – Accessories). Set the depth of cut, plug in the mains supply and then place

the base plate (14) onto the work surface. Ensure that the front indication mark on the

base plate aligns with the start line.

 Switch on the tool and wait for a moment until the blade reaches full speed. Next, plunge

the blade slowly and gently, but firmly into the material. Then push the tool forwards along

the line to be cut. (Never draw the tool backwards)

 Once the finish line has been reached, lift the tool from the work surface before switching

off. If a lot of dust has been created, keep switched on for extra few seconds to allow the

dust being discharged from the tool.

10 CUT-OUTS

10.1 Cutting out tips:

 If the cut is to be covered, for example by a vent cover, the corners can be overlapped to

ensure that the waste material is completely detached. (Fig. 9)

 If the cut out is to be seen, do not overlap the corners. In this circumstance, as the cutting

blade is circular, the waste material will not be fully detached. The corners will therefore,

require finishing with a knife. If the material is thin and the back surface unimportant, the

waste material can just be pushed out. (Fig. 10)

 Where there is access to the back surface of the material to be cut, the cut out can be

marked out with an over cutting allowance. The cut is then made from the back surface to

ensure perfect corners on the front surface. (Fig. 11)

10.2 Cutting particularly Tough or Abrasive Materials

10.2.1 Sheet metal:

 Only use a blade specifically designed for this purpose.

 Always set the depth adjustment to at least 1 mm deeper than the material thickness to

avoid the blade riding up over the surface. Scrap material is required underneath the work

surface.

 Remove burrs and rust as these impede the feed across the material.

 Thick beeswax (furniture polish) applied to the base plate of the tool makes metal cutting

easier. (the base plate will slide easier over the work piece)

 Only suitable for cutting brass, copper, lead, aluminium or galvanised mild steel.

 Every 2 minutes of metal cutting should be followed by a rest of at least 3 minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX1425 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX1425

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info