675038
13
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
POWX225 EN
Copyright © 2019 VARO P a g e | 13 www.varo.com
11 CLEANING AND MAINTENANCE
Before performing any work on the equipment, pull the power plug.
11.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
Make sure no water can reach the inside of the power tool!
11.2 Lubrication
All motor bearings are permanently lubricated at the factory, and do not require any additional
lubrication. Use graphite or silicone to lubricate all mechanical parts of the table saw where a
pivot or threaded rod is present. Dry lubricants do not hold sawdust like oil or grease.
12 TROUBLESHOOTING GUIDE
Possible causes
Corrective action
The saw is not plugged in.
The fuse has blown or the
circuit breaker has tripped.
The cord is damaged.
Plug in the table saw.
Replace the fuse or reset the
circuit breaker.
Have the cord replaced by a
qualified electrician.
The positive stop is not
adjusted correctly.
Check the blade with the square
and adjust the positive stop.
The blade tilt pointer is not
set correctly.
Check the blade with the square
and adjust the positive to zero.
The rip fence is not properly
aligned.
Align the rip fence with the miter
gauge slot.
The rip fence is not aligned
with the blade.
Check and adjust the rip fence.
The wood is warped, or the
edge that is against the fence
is not straight.
Select another piece of wood.
The splitter is not aligned
correctly with the blade.
Check and align the splitter with
the blade.
The blade is dull.
Replace the blade.
The blade is mounted
backwards.
Turn the blade around.
There is gum or pitch on the
blade.
Remove the blade and clean it
with turpentine and coarse steel
wool.
The blade is not appropriate
for the work that is being
done.
Change the blade.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POWX225 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POWX225

Powerplus POWX225 Bedienungsanleitung - Deutsch - 18 seiten

Powerplus POWX225 Bedienungsanleitung - Holländisch - 16 seiten

Powerplus POWX225 Bedienungsanleitung - Französisch - 16 seiten

Powerplus POWX225 Zusatzinformation - Alle Sprachen - 7 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info