Bedienungsanleitung Powerplus POWXQG7556 (Seite 13 von 17) (Englisch)

481032

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

POWXQG7556 EN

Be sure to carefully balance blade after sharpening. The blade can be tested for balance by

balancing it on a round shaft screwdriver. Remove metal from the heavy side until it balances

evenly.

Before reassembling the blade and the blade adapter to the unit, lubricate the engine

crankshaft and the inner surface of the blade adapter with light oil. Install the blade adapter on

the crankshaft with the "star" away from the engine. Refer to figure 15. Place the blade with

the part number facing away from the adapter. Align the washer over the blade and insert the

hex bolt. Tighten the hex bolt to the torque listed below:

9.3.3 Blade mounting torque

Centre Bolt 40 Nm-50 Nm, to insure safe operation of your unit. ALL nuts and bolts must be

checked periodically for correct tightness.

After prolonged use, especially in sandy soil conditions, the blade will become worn and lose

some of the original shape. Cutting efficiently will be reduced and the blade should be

replaced. Replace with an approved factory replacement blade only. Possible damage

resulting from blade unbalance condition is not the responsibility of the manufacturer.

When you change the blade you must use the original type marked on the blade.

10 STORAGE INSTRUCTIONS (OFF SEASON)

The following steps should be taken to prepare lawn mower for storage.

1. Empty the tank after the last mowing of the season.

 Empty the petrol tank with a suction pump.

Caution! Do not drain the petrol in closed rooms, in close proximity of open

fire, etc. Do not smoke! Petrol fumes can cause explosion or fire.

 Start the engine and let it run until it has used up all remaining petrol and stalls.

 Remove the spark plug. Use an oilcan to fill approx. 20 ml oil into the combustion

chamber. Operate the starter to evenly distribute the oil in the combustion chamber.

Replace the spark plug.

2. Clean and grease the lawnmower carefully as described above under “Lubrication”.

3. Slightly grease the cutter to avoid corrosion.

4. Store the lawnmower in a dry, clean and frost-protected place, out of reach of

unauthorized persons.

Caution! The engine must have completely cooled down before storing the

lawnmower.

NOTE:

 When storing any type of power equipment in an unventilated or material storage shed,

care should be taken to rust-proof the equipment. Using a light oil or silicone, coat the

equipment, especially cables and all moving parts.

 Be careful not to bend or kink cables.

 If the starter rope becomes disconnected from rope guide on handle, disconnect and

ground the spark plug wire, Depress the blade control handle and pull the starter rope out

from engine slowly. Slip the starter rope into the rope guide bolt on handle.

11 TRANSPORT

Turn the engine off. Ensure not to bend or damage the cutter when pushing the lawnmower

over obstacles.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXQG7556 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXQG7556

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info