Bedienungsanleitung PowerTech PT25-EC (Seite 64 von 66) (Englisch)

685338

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

ELECTRICAL CONNECTIONS

ELECTRICAL WIRING

All wiring must be applicable with local electrical codes. A qualified licensed electrician must

perform all electrical wiring connections. Ground Fault (GFCI) breakers must be installed to protect all

vehicle branch circuits. All switches and controls must be securely mounted to prevent damage and

accidental opening or closing from vibration, road shock and vehicle motion.

Battery, load leads and the remote switch panel connections are necessary for completing the

installation. Make final connections to the battery only after all other connections have been made, as this

will prevent unintentional starting. Some specific details on each connection are stated in the following

paragraphs. Refer to the wiring diagram for specific details. All wiring to the generator set shall be securely

supported or harnessed to prevent abrasion. Additional support is required to prevent exposure to the exhaust

system and any possible leakage of fuel, oil, or grease. At least 2 inches of clearance must be maintained

between electrical wiring and hot exhaust parts. Wiring must not be located directly below or close to the

fuel system, oil fill and drain locations. If the coach is equipped with a mechanism for removing the

generator set from the compartment such as a mounting base or slide rack, be certain all wiring is long

enough to allow for free movement of the generator for servicing.

A separate 12-volt battery is recommended for the generator set. With a separate battery, cables

should be kept short in length thus eliminating problems with excessive voltage drop. See the Table below

for cable size (AWG) to length requirements.

NOTE: A heavy gauge #4 ground strap must be connected between the ground lug on the generator set and

the frame of the vehicle. All wiring connections made at the time of installation should be readily accessible

for periodic inspection and servicing.

DISTANCE BETWEEN

GENERATOR SET AND

BATTERY

CABLE SIZE (AWG) REQUIREMENTS

AT VARIOUS TEMPERATURES

0°F (-18°C) 32°F (0°C) 75°F (24°C)

40’ (12.2M) 00 0 1

30’ (9.2M) 0 1 2

25’ (7.6M) 1 2 4

20’ (6.1M) 2 2 6

15’ (4.6M) 2 4 6

10’ (3.0M) 4 6 8

5’ (1.5M) 6 6 8

2.5’ (0.8M) 8 8 8

AC LOAD LEAD CONNECTIONS

Some generator sets have four color-coded leads. The Black leads (L1 & L3) are hot. The White or

Gray lead (L2) is neutral and the Green lead is ground. The load leads can be routed directly from the

junction box to the vehicle AC circuit or transfer switch connection. All installations require that the load

leads be routed through flexible conduit from the generator end bracket to the junction box location. The

load lead junction box must be accessible for servicing and inspection.

AC load lead (L2) White or Gray is always the neutral lead on PTS generator sets. Make sure the

neutral of the AC circuit in the vehicle is connected to the (L2) White or Gray lead. If equipment ground type

plugs and receptacles (3 prong) are used in the vehicle, the green wire must be connected to the chassis

ground. On vehicles, which also have provisions for using an outside AC, power source, the neutral lead as

well as the Black (L1 & L3) hot leads must be completely isolated from the generator set when power is

switched to the outside source.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

PowerTech PT25-EC Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info