Bedienungsanleitung Profile PAC-308 Vivace (Seite 1 von 2) (Englisch)

566740

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

VIVACE – Cordless doorbel set UK - 1

PAC-308

Thank you for purchasing this Profile product. Please

note: It is important that you read this manual before

using the product. And be sure to save this manual for

possible use later.

The cordless doorbell consists of 2 separate

components:

1. Push-button unit (transmitter)

2. Bell unit (receiver)

These items are completely independent of each other

and require no wiring.

When the push-button is pressed in, a signal is sent to

the bell, whereupon the bell is activated. Since it has a

range of up to 50 meters (in open spaces) you can use

the bell virtually anywhere in the house, workshop,

office, set it up in the garden or just carry it with you.

Battery installation

Push-button unit

1. The push-button unit works using 1 x 3v

(CR2032) lithium battery (included).

2. The lithium battery is already installed. Open

the push-button and remove the insulator

strip.

3. Snap the rear side back into position, and the

push-button is ready for use.

To replace the battery:

1. Open up the push-button unit.

2. Remove the metal plate using a screwdriver.

3. Place a 3v battery (CR2032) in the battery

compartment, making sure the positive

terminal (+) is uppermost.

Bell unit

1. Slide the rear cover open.

2. Place 2 AA alkaline batteries into the battery

compartment.

3. The bell unit will produce a two-tone signal,

indicating that it is ready to read a digital code

(see channel selection).

4. Slide the cover firmly back into place; the bell

is now ready for use.

Installation

Push-button unit

Use the two small holes on the

rear of the push-button to mark

the position for securing in

place. Drill small holes and

mount the push-button in

position with screws (self-

tapping 3 x 16mm, included) or

use the double-sided adhesive

tape (included).

Important: If you secure the

push-button onto a metal

upper surface or PVC type of

door (with metal), its maximum range of transmission

will be greatly reduced.

Bell unit

This bell can be used as a portable device - or fixed into

position. On the reverse side, there are two suspension

slots, with which the bell can be hung up using a screw,

and can easily be taken down again. Drill a small hole

and fix a rawlplug in place. Mount the hook (included)

onto the wall using a screw. The bell unit can hung up

safely in this way.

Choice of bell tone

The bell-tone selector button is inside the push-button

unit, below letter “S”. Press the button once to hear the

bell tone already set. Press again to hear and select the

next tune.

1. Long Westminster chime 2. Ding-Dong

3. Telephone ring 4. Circus theme

5. Banjo on my knee 6. Twinkle-twinkle

7. It’s a small world 8. Barking dog

Optionally: It is possible to install an extra push-button

by your back door. By applying the procedure given

above, each push-button can produce a different tune.

Channel selection

The unit is supplied with a pre-set radio frequency. If by

chance the bell should sound for no apparent reason,

it's possible that another device nearby is using the same

frequency. To get round this problem, you can change

the frequency of the push-button and bell.

1. remove the cover behind the push-button.

2. To program or change: remove the batteries

from the bell unit for at least 30 seconds to

prime the memory.

3. place the batteries back into position within.

Press the push-button after the two-tone signal

sound (with a second press of the button if

need be) to confirm the new code. Do this

within 1 minute. Don’t use any other cordless

products for the next 5 minutes.

4. Test for correct operation.

Trouble-shooting and tips

Problem: Bell rings, but LEDs fail to light up

Possible cause: - The bell is out-of-range (max.

100m in open spaces)

Possible solution: - Move the bell within range

- Reprogram the channel (see

channel selection)

Problem: Bell does not ring, nor do the LEDs

light up

Possible cause: - Push-button battery is flat

- Batteries are not correctly installed

in the push-button

Possible solution: - Replace battery

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PAC-308 Vivace Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Profile PAC-308 Vivace

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info