Bedienungsanleitung Profile PCF-635 (Seite 1 von 2) (Englisch)

566788

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

ENERGY CONSUMPTION METER UK - 1

PCF-605

Thank you for purchasing this Profile product. Please

note: It is important that you read this manual before

using the product. And be sure to save this manual for

possible use later.

Please note

The Energy Meter must be charged before use.

After 15 minutes, the LCD screen will be

operational, but to fully charge the battery, the

device must be plugged into the mains for at least

12 hours.

The Energy Meter is the easiest way for you to

measure the energy costs of connected appliances.

Technical data

 Operating voltage: 230V AC (50/60 Hz) alternating

current (AC)

 Maximum power of connected appliances: 3680 W

 Maximum current: 16A

 Input/ Output: via earthed socket

 Operating temperature: + 10 to +40° C

 Energy display: 0 kWh to 999.9 kWh

 Maximum registration time: 9999 hours

 Only use indoors (IP20)

Correct use

The measurement range of the Energy Meter is 5W to

3680W. Exact measurement of values below or above

this range is not possible. Use outside this range can

overload and damage the unit.

 The Energy Meter was designed to monitor and

measure electric appliances.

 The Energy Meter is approved only for use with

230V AC.

 Only 230V AC, 50/60Hz electric appliances may be

connected.

 The maximum power of the connected loads may

not exceed 3680W (maximum amperage 16A).

 Use of the Energy Meter is only allowed indoors in

dry environments. Use in the open air is strictly

prohibited!

 Always heed the instructions on the identification

label located on the connected power cables.

 Use other than that described above can result in

damage to the product and the risk of short circuit,

fire, electric shocks, etc.

 The product as a whole may not be converted or

modified. The safety instructions must be followed

strictly.

Safety instructions

 The manufacturers accept no liability for damage to

objects or persons that arises from incorrect use or

noncompliance with the safety prescriptions. All

damage claims resulting in such cases are void.

 The Energy Meter may only be connected to

regulated outlets (230V AC, 50/60Hz- 10/16A) with

a ground.

 The connected appliances may not use more than

3680W (16A).

 The operating temperature of the connected

appliance must be between 10º and 40º.

 High temperatures, especially when measuring high

levels of electrical power, can result in overheating

and damage to the Energy Meter.

 Avoid use in extreme weather conditions and in the

vicinity of inflammable gases, moisture and dust.

 For safety reasons, the unit may never be operated

in a wet or damp environment.

 During cleaning or maintenance, disconnect each

source of power from the Energy Meter. The battery

and the LCD screen can retain a charge, even when

the unit is disconnected from all sources of power.

 Insert no metal parts or other objects in the Energy

Meter.

 If it is established that safe use is no longer

possible, take the Energy Meter out of operation and

ensure that it is not mistakenly put back into

operation by someone else. If there is visible

damage to the Energy Meter, it must be taken out of

service immediately.

Features

 Display of current time (24-hour clock), day, energy

consumption in Watts and billing rate.

 Display of total time connected, energy consumed

and the cost of energy consumed.

 Display of total registered times, total time and

percentages.

 Programmable day and night rates.

Configuration, connection and operation

 The procedure for setting the time and the billing

rate is the following:

Setting the current time and day

1. Simultaneously press the “+” and ”-

“ buttons to enter the system

configuration. The first setting is the

current time.

2. Use the “+” button to increase the

value of the flashing position from 0 to

9; use the “-“ button to decrease the value of the

flashing position.

3. Press the “MODE” button to move the next position.

4. After setting the day, push the “MODE” button again

– billing rate 1 for the system can now be configured.

Setting billing rate 1 (day rate)

1. Set the start time for billing rate

1. For example day rate starts at

7.00 a.m.

2. Set rate 1. All values are

introduced in quantities of eurocents.

E.g. 1.00€ = 100cent

3. Use the “+” button to increase the value of the

flashing position from 0 to 9; use the “-“ button to

decrease the value of the flashing position.

4. Press the “MODE” button to move to the next

position.

5. Press the “MODE” button - billing rate 2 for the

system can now be configured.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PCF-635 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Profile PCF-635

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info