Bedienungsanleitung Profile PLI-152 (Seite 1 von 2) (Englisch)

566844

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

HALOGEN HAND LAMP ELLIPS 500W

EN - 1

+ movement sensor

PLI-150 black

PLI-152 metal

We thank you for the purchase of this Profile product.

Note: It is important that you read this manual carefully

before using the product and be sure to save this manual

for possible use later.

Note

Check if building regulations apply to your area whereby

you must have the halogen hand lamp installed by an

accredited electrician. An electrician can give you

information about correct wiring. Never install the fitting

outside in rainy weather.

SWITCH OFF THE POWER BEFORE YOU INSTALL

THE HALOGEN HAND LAMP.

Correct installation

 With installation outside preferably choose a place

under a roof.

 Do not place the sensor head in direct or reflected

sunlight. The halogen hand lamp may then switch on

when not required. The sensor works best with

movement “crosswise” through the sensor's detection

field.

 Connect the halogen hand lamp to a circuit with wall

switch.

 Unscrew the stainless steel bolts on the side to take

the holder from the fitting.

 Fix the holder to the wall with 2 screws. Do not fix the

holder to a highly flammable surface. Leave a distance

of at least 1 m between the halogen hand lamp and the

object to be illuminated. (see fig. 2) Install the halogen

hand lamp at least 2.5 m above the ground. (see fig.1)

Fig. 1 Fig. 2

 Fix the halogen hand lamp back on the assembled

holder.

 Remove the cover of the cable connection.

 Pull the power supply wires through the opening with

the rubber packing.

 Connect the electric wiring according to figures 3 and

 The halogen hand lamp must be connected to mains

voltage of 230V, max. fusing 16A.

 Screw the cable connection cover tight again.

Fig. 3

Fig. 4

 Always respect the instructions on the identification

label of the connected power cables.

 Other uses than described above can cause damage

to the product and increase the risk of short-circuit,

fire, electric shocks, etc.

 The product may not be adapted as a whole. The

safety instructions must be strictly observed.

Safety instructions

 The importer accepts no responsibility for damage

claims with respect to objects or persons that result

from incorrect use or non-compliance with the safety

instructions. Any damage claims in such cases will

be declared null and void.

 When replacing the halogen bulb the lamp must first

have cooled before the bulb is replaced. Also

disconnect the power supply. Do not exceed the

maximum wattage of 500W.

 CAUTION: Never touch the bulb with your fingers.

 Touching the bulb with your fingers can reduce the

life of the bulb.

 Always replace cracked or broken glass by glass

with the same properties as the original glass.

Technical information

 Working voltage: 230V AC (50/60 Hz)

 Maximum lamp power: 500W.

 Maximum current strength: 10/16A.

 Dustproof and splash proof: IP44.

 Passive infrared sensor (PIR).

 Sensor angle: 120°.

 Sensor range: 12 - 15 meters at with 25°C.

 Lighting time: +/- 10 sec. – 10 min.

L = phase

= earthing

* N

= neutral wire

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PLI-152 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Profile PLI-152

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info