301373
1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
191817
USER’S MANUAL
PDX-1100
Series
DECLARATION OF CONFORMITY
Hereby, Hesdo declares that the radio equipment type Profoon PDX-
1100 is in compliance with directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:
http://DOC.hesdo.com/PDX-1100-DOC.pdf
INSTALLATION
Base station:
1. Plug the small connector at the phone cable into the back of the base
station (press the connector until you hear a click).
2. Plug the phone connector into the phone socket.
3. Plug the low voltage connector of the adapter into the backside of the
phone, and plug the adapter into a 230 Volt mains socket.
Handset:
1. Open the battery compartment of the handset, by sliding the battery
cover down and insert the batteries into the battery compartment; at
this, pay attention to the polarity (+ and -).
2. Slide the battery cover back onto the handset and place the handset
on the base station. Leave the handset continuously during 15 hours
on the base station, to charge the batteries properly.
Extra handsets and chargers:
If your phone has been delivered with multiple handsets, 2 batteries
and a charger with adapter will be included for every handset. Plug the
adapter of these chargers in a 230 Volt mains socket, insert the batteries
into the handset(s) and place the handset(s) on the charger(s) to charge
the batteries.
ONLY CONNECT THE INCLUDED ADAPTER. CONNECTING
OTHER ADAPTERS MAY RESULT IN DANGEROUS SITUA-
TIONS OR MAY CAUSE DAMAGE TO THE ELECTRONICS
OF THE PHONE.
1 2
5. Use key to delete the old name and enter the new name through
the keyboard.
6. Press the key .
7. Use key to delete the old number and enter the new number
through the keyboard.
8. Press the key
9.
Select the desired VIP ring tone for this number with and .
10.Press the key to save the corrected memory.
Delete memory selectively:
1. Press the key
2. Search the desired memory, using keys and .
3. Press the key
4. Search the option [DELETE] with the keys and .
5. Press key to delete this memory.
Delete memory completely:
1. Press the key
2. Press the key
3. Search the option [DELETE ALL] with the keys and .
4. Press key twice to delete the memory completely.
Memory status:
You can see how many storage locations you have used of the 50
available:
1. Press the key
2. Press the key
3. Search the option [PB STATUS] with the keys and .
4. Press the key
, f
or example, the following appears on the display:
15/50 OCCUPIED (15 of the 50 memories are in use).
5. Pressthekeyphone-o󰀨thricetoreturntotheidlemodeofthehand-
set.
PHONE BOOK MEMORY
Introduction:
Every handset has a phone book memory with a capacity of 50 phone
numbers of at most 20 digits. You can program a name of at most 12 char-
acters with each number.
The phone book memory in the handset is connected to the function Caller
Identication.Whenyouarecalledbysomebody,whosenameandnum-
ber you have programmed in the memory, the name of this person is also
displayed beside the number on the display of your handset. However, for
thisyouneedtosubscribetotheserviceCallerIdentication.
Programming:
1. Press the key once and the key twice.
2. Enter the name through the keyboard (see the ABC on the dial keys).
You can delete an incorrect input with key
3. Press the key
4. Enter the number through the keyboard.
You can delete an incorrect input with key
You can add a dial pause with key 0
5. Press the key
6.
Select the desired VIP ring tone for this number, using
and
7. Press the key to store the memory
Dialing:
1. Press the key
2. Search the desired memory, using keys and .
3. Press on the phone key to dial this number.
Changes:
1. Press the key
2. Search the desired memory, using keys and .
3. Press the key
4. Search the option [EDIT] with the keys and , press the key
Handset volume:
1. During the call, press the keys or , to increase or decrease the
volume.
R/Flash:
1. Press the key R to give a FLASH pulse. The interruption time
the FLASH pulse is adjustable; see for this the chapter PHONE
SETTINGS.
Mute (microphone o󰀨):
1. To disable the microphone, shortly press the key during the call.
You can still hear the other party, but they cannot hear you.
2. To enable the microphone again, shortly press the key again.
Search handset:
1. Shortly press the key on the base station.
During 60 seconds, a signal will sound from the handset, and the
word ‘PAGING’ ashes on the display of the handset. Press the key
phone-o to end the signal prematurely.
Call timer:
1. During the phone call, the elapsed call duration is displayed on the
display.
Quick key bell o󰀨:
1. To disable the bell of the handset, press key for more than
2 seconds.
2. To enable the bell again, press key for more than 2 seconds.
INSERT ONLY RECHARGEABLE NiMH (NICKEL METAL
HYDRIDE) BATTERIES. THE USE OF NOT RECHARGEABLE
BATTERIES MAY CAUSE DANGEROUS SITUATIONS OR
EXPLOSION HAZARD.
OPERATION
Answering calls:
1. Press the key phone-on to accept a call. See
chapter PHONE SETTINGS to accept a call directly by only taking
the handset from the base station or the charger.
Making calls:
Block dialing:
1. Enter the phone number through the keyboard.
You can delete an incorrect entry with key
Press key 0 for a dial-pause
2.
Press the phone-on key to dial the number
Direct dialing:
1. Press the phone-on key and wait for the dial tone.
2. Enter the phone number through the keyboard; this number will be
dialed directly.
End the call:
1. Pressthekeyphone-o󰀨toendacall
The end the call, you can also place the handset back on the base
station or the charger.
Key lock:
1. To enable the key lock, keep the key pressed for more than 2
seconds.
2. To disable the key lock, keep the key pressed for more than 2
seconds again.
LAST NUMBER MEMORY
The handset will remember the last 5 numbers dialled with it.
Redialing:
1. Press the key , the last number you dialed appears on the display.
2. Search the desired number with and .
3. Press on the phone key to dial this number.
Copying to the phone book memory:
1. Press the key .
2. Search the desired number with and .
3. Press the key twice
4. Enter the name through the keyboard.
5. Press the key twice
6. Select the desired VIP ring tone for this number with and .
7. Press the key to store the memory
Delete last dialed number selectively:
1. Press the key .
2. Search the desired number with and .
3. Press the key
4. Select the option [DELETE] with and .
5. Press the key to delete this memory
Delete the complete last number memory:
1. Press the key .
2. Press the key
3. Select the option [DELETE ALL] with and .
4. Press the key twice, to delete the complete last number memory.
Tip: you can also open the last number memory by pressing the key
from the idle mode of the handset.
3
. Forwarding:
As soon as the called handset
answers,pressthephone-o󰀨
key; the outside line is now
forwarded.
Registration:
1. Press the key
and select the option [REGISTRATION].
2. Press the key
and enter the PIN code (de factory code 0000 or
your own PIN code) and press the key
The handset will search for the concerning base station
3.
Hold the key
on the base station during 15 seconds.
4. After a few seconds a beep tone will sound from the handset, and the
handset has been registered. At the right side of the display the
internal number of this handset is displayed (1~6).
Deregistration of handsets:
Handsets that are faulty shall be deregistered.
1. Press the key
and select the option [BS SETTINGS].
2. Press the key twice, and enter the PIN code (de factory code
0000 or your own PIN code).
3. Press the key
and select the handset that you want to deregister*.
4. Press the key
;
the selected handset is deregistered now.
* You can only deregister other handsets; you cannot deregister your
own handset.
PHONE SETTINGS
Introduction:
1. Open the menu by pressing the key .
2. Browse through the menu options by using and .
3. Press the key to open the desired option.
4. Makeachoiceorselect‘on’or‘o󰀨’withthekeys and .
5. Finally, press the key to save the settings.
MULTIPLE HANDSETS
Introduction:
You can connect (register) up to 5 wireless handsets to the PDX-1100
serie. Withmultipleregisteredhandsets,youcancalleachotherfor
free in and around the house and forward calls or even call with three
people.
If the phone has been delivered with one handset, u can purchase extra
handsets(*),whichyoushallregisterrst(seetheconcerninginstructions
further in this user manual). If the phone has been delivered with multiple
handsets, you can make internal calls and forward calls directly.
* Pay attention to the fact that these shall be ‘GAP COMPATIBLE’ hand-
sets. GAP means that handsets and base stations of other types and/or
brands are interchangeable.
Intercom:
1. Press the key
2
. 2 handsets in use:
In case 2 handsets have been
registered with your phone, the
other handset will ring
immediately.
3. You can make the intercom call, as soon as the called handset an-
swers.
Forwarding/conference:
1. During the call with the outside line, press the key twice.
2
. 2 handsets in use:
In case 2 handsets have been
registered with your phone, the
other handset will ring
immediately.
Delete call selectively:
1. Press the key ; the name or the number of the last received call
appears on the display.
2. Search the desired call with and .
3. Press the key and select the option [DELETE] with and .
4. Press the key to delete this call.
Delete complete call history:
1. Press the key ; the name or the number of the last received call
appears on the display.
2. Press the key
and select the option [DELETE ALL] with and .
3. Press the key twice, to delete the complete call history.
Voicemail indication: ( )
In case the carrier left a Voicemail message for you, this is shown on the
displaywithanilluminatingenvelope.Thissymbolgoeso󰀨assoonasyou
have listened to this message.
Attention: this function is only available on the FSK system and when
this is supported by the carrier.
CALLER IDENTIFICATION
Introduction:
IfyouhavetheserviceCallerIdenticationatyourdisposal,thenumber
of the calling party is displayed on the display of your handset(s). If your
carrier also transmits names, or you have programmed this number
including name and the phone book memory of the handset, the name is
alsodisplayedonthedisplay.TheCallerIdenticationmemoryhasaca-
pacity of 10 numbers. Attention: when this memory is full, every following
incoming call will overwrite the oldest call in the memory.
New calls:
This display indicates whether and how many new calls are stored in the
CallerIdenticationmemorythatyouhavenotseenyet.Assoonasyou
haveviewedthememory,thisnoticationgoeso󰀨.
View memory and callback:
1. Press the key ; the name or the number of the last received call
appears on the display.
2. Browse through the memory by using and .
When a name is displayed, press the key # to view the number. Press
the key and select DETAILS, to view the time and date of the
call.
3. Press the phone key to call back this subscriber.
Copying to the phone book memory:
1. Press the key : the name of the number of the last received call
appears on the display.
2. Search the desired call with and .
3. Press the key twice, and enter the name through the keyboard.
4. Press they key
twice, and select the desired VIP ring tone with
and .
5. Press the key to store the memory.
6. Pressthekeyphone-o󰀨toreturntotheidlemodeofthehandset.
Menu structure:
The menu structure of the phone looks as follows:
RING SETUP
PHONEBOOK
BS SETTINGS
DELETE HS
FLASH TIME
CHANGE PIN
HS SETTINGS
ALARM
RING SETUP
INT. RING
EXT. RING
RING VOLUME
TONE SETUP
LANGUAGE
RENAME HS
HS DISPLAY
AUTOANSWER
DATE & TIME
REGISTRATION
DEFAULT
Ring signals:
Select the option [RING SETUP] to select the ring tones of the handset:
- You can set dierent melodies for intercom calls and calls from outside.
- You can chose from 5 dierent melodies for [INT. RING] and [EXT.
RING].
-
You can chose from 5 volume levels and ‘volume-o’ for [RING VOLUME].
Handset tones:
You can enable or disable the following tones through the option [TONE
SETUP]:
- [KEY TONE]: the tones that sound when you press a key.
- [BATTERY TONE]: the tones that sound when the batteries are low.
- [OUT OF RANGE]: the tones that sound when you get out of reach.
Power failure:
This phone obtains its power supply from the mains power. In case of
failure of the mains power, this phone cannot be used. Therefore it is
advisable to keep a wired phone in reserve.
Hearing aids:
Users of older generation hearing aids always shall keep into account a
possible uncomfortable buzzing tone when using DECT phones.
Eavesdropping:
Eavesdropping on a DECT phone is virtually impossible. Not only shall
one be within reach of the DECT phone, one also needs expensive
equipment.
Maintenance:
Clean the phone only with a moist cloth; do not use any chemical
detergents.
The adapter and the phone cable shall be disconnected before
cleaning.
Medical equipment:
It is possible that enabled DECT phones interfere with sensitive medical
equipment.Whenthephoneiskeptinthevicinityofthemedicaldevice,
interference can occur. Do not place a DECT phone on or near a medical
device, not even when it is in standby mode.
Power supply handset:
The display of the handset is provided with a built-in battery capacity
meter:
: The complete symbol flashes when the batteries are charged.
Only the inner part flashes when the batteries have been
charged.
: The indication that the batteries shall be charged flashes when
the batteries are low.
• Werecommendplacingthehandseteveryeveningonthebase
station or charger, for optimal use. This does not have an adverse
e󰀨ectontherechargeablebatteries.
Factory settings:
You can reset the settings the way they were when the phone left the
factory, through the option [STANDARD]:
Name handset: handset
Display language: Dutch
Ring volume: level 3
Call melody external call: melody 1
Call melody internal call: melody 2
Reception volume: level 3.
Show handset: on
Key lock: off
Alarm: off
Auto answer: off
Date format: day-month-year
Hour format: 24 hours
Flash time: short (100 ms)
The memories stay undisturbed with this reset instruction.
TIPS AND WARNINGS
Range:
The range of the phone is up to 300 meters in the open field and up to
50metersinside;therangedependsonlocalcircumstances.Whenyou
get out of reach of the base station, the symbol will start flashing and
the text [SEARCHIG] appears on the display. In this state, you cannot
receive or make any calls. In case the power supply adapter of the base
station is unplugged from the mains socket, the handset will lose contact
with the base station, the display will display [SEARCHING], and the
antenna symbol will start flashing. The handset will restore contact with
the base station within several minutes after the power supply adapter
has been plugged in again.
Name handset:
Youcannameyourhandsetthroughtheoption(NWNAMEHS).Use
key to delete the old name and enter the new name of at most 10
characters through the keyboard. Press the key to save the name.
Flash time:
A flash pulse is a very short interruption the phone connection. You can
set the interruption time of the FLASH pulse on [SHORT] (100 ms), [ME-
DIUM] (300 ms) or [LONG] (600 ms). 100 ms is the standardized inter-
ruption time, and this time is set at the factory. Refer to the user manual
of your home or office switchboard or consult your carrier concerning the
desired interruption time.
PIN code:
You can change the PIN code, which you need with registering and
deregistering of (new) handset, with [CHANGE PIN]. The factory PIN
code is 0000. See chapter ‘SYSTEM RESET’, in case you have lost or
forgotten the new PIN code.
Date and time:
At idle, you can display the time on the display of the handset, an at
Caller Identification, the time and date of the call are registered.
You can chose from the formats day-month-year or month-day-year
at [DATE FORMAT], and you can chose from 12 hour or 24 hour time
format at [TIME FORMAT]. Enter the time and the date at the respective
options [SET TIME] and [SET DATE].
Answering automatically:
Whenthefunction[AUTOANSWER]isenabled,youcanacceptcallsby
only taking the handset from the base station or charger; then you do not
need to use the phone key. Attention: In case the handset is not placed on
the base station or the charger, you always need to press the phone-on to
accept a call.
Alarm: (alarm function)
You can set the phone to sound an alarm tone during 40 seconds at a
presetmoment(orpressanykeytoswitcho󰀨thesignalprematurely).
Select ON to enable this function, and enter the alarm time through the
keyboard (24 hour system). After this, you can enable or disable the
snooze function. The alarm is not repeated automatically daily.
Displaying name or time on the handset:
At idle, you can display the name or the actual time of the handset on
the display of the handset, through the option [DISPLAY HS].
Language:
Here you can set the language in which the various instructions are
displayed on the display.
Instructions to revert to the English language, in case you have set a
foreign language accidentally:
1. Press the key ‘phone-o’ 3 times.
2. Press the key once.
3. Press key thrice.
4. Press the key once.
5. Press key thrice.
6. Press the key once.
7. Select the English language with and .
8. Press the key once.
9. Press the key phone-o to return to the idle mode of the handset.
Rechargeablebatteriesorbatterypacksshallnotbeexposedtore
or extreme heat.
Never cut open batteries of battery packs. The content is chemical
and poisonous.
POSSIBLE PROBLEMS AND SOLUTIONS
Problems with incoming calls:
• Nonoticationofincomingcalls:
- The bell is disabled; enable it.
You are continuously busy:
- Check whether a 2nd phone or a 2nd handset that has been
registered with the base station, is using the line.
- Connect another phone to your phone connection, and use this to
check whether the malfunction originates from your connection or
your carrier.
Problems during calling:
Beep tones during an intercom call:
- You are called from outside during an intercom call; end this call,
wait until the phone rings normally and answer the call.
Noise and other distortions:
- You are getting out of reach of the base station; reduce the
distance.
- There are other electrical devices in the vicinity that interfere with
the radio waves of your DECT phone; try another location.
Problems with Caller Identification:
• YoudonotreceiveNameorCallerIdenticationinformationonthe
display of your handset.
- Check whether your carrier transmits these signals (you shall
subscribe to this service with some providers).
3 4
56 7 8 9
10 11 12 13 14
15 16
v1.3
You do receive the numbers on the display of your phone, but not the
name.
- The carrier does not forward names; consult your carrier for this.
- The name has not been programmed in the memory of your
handset; program it.
- The name has been programmed in the memory, but the
accompanying phone number has been programmed without area
code; program the number including area code.
Other:
The display stays blank:
- The batteries are empty. Place the handset on the base station or
on the charger to charge the batteries, and let the handset charge
during at least 15 hours uninterrupted.
The handset does not switch on:
- The battery voltage is too low; place the handset on the base
station or the charger and charge the batteries for 15 hours.
- The batteries have not been inserted; check this.
The batteries get low too fast:
- Check the charging contacts of the base station or the charger and
of the handset, and clean them if necessary.
- The batteries shall be replaced; replace them.
The handset does not have contact with the base station:
- You are too far from the base station; reduce the distance.
- The base station has been switched off (adapter from the mains
socket); correct this.
- The handset is not registered with the base station (anymore);
register it (again).
In case the failure has not been solved with aforementioned solutions:
Remove the batteries from the handset, and unplug the power supply
adapter and the phone connector from their sockets; connect everything
again after several minutes.
SYSTEEM RESET (forgot PIN code)
If you have lost or forgotten the new PIN code, or if the phone does not
respond anymore, you can completely reset the phone, at which the PIN
code is reset to 0000. Take care to deregister the handset(s). You shall
register it again.
1. Unplug the adapter from the mains socket.
2. Press the key on the base station AND KEEP THIS KEY PRESSED.
3. Plug the adapter back into the mains socket (keep key pressed).
4. Release the key AFTER 30 SECONDS; the phone had been reset.
5. Now register the handset(s) again, as described in chapter ‘Multiple
handsets’.
SPECIFICATIONS
Protocol: DECT / GAP, 5 handsets
Frequency Range: 1880-1900 Mhz
Maximum Power: < 24 dBm
Call history: DTMF & FSK, auto recognition, 10 memories
FLASH : 100/300/600 ms, adjustable.
Phone book: 50 memories
Power supply base station: through adapter
in: 100 - 240 VAC 50 Hz
off: 6 VDC, 450 mA,
Power supply handset: through 2 batteries
voltage: 1.2 V
capacity: 300 mAh
material: NiMH
format: AAA or HR03
Power supply charger: through adapter
in: 100 - 240 VAC 50 Hz
off: 6 VDC, 450 mA
Range: 50 m indoors/300 m outdoors
Operational life: standby: > 100 hours, use: > 10 hours
Operational temperature: 0 °C to 40 °C
Storage temperature: -20 °C to 60 °C
Loading factor: 12.5
DISPLAY
The following symbols can illuminate on the display:
Illuminates continuously: the
handset is within reach of the
base station; flashes: the handset
is out of reach of the base station.
Flashes during connecting
an intercom call; illuminates
continuously during an intercom
call.
Flashes when u are called from
outside; illuminates continuously
during a call on the outside line.
Illuminates continuously when the
alarm function has been enabled;
flashes when the alarm goes off.
You have received a voicemail
message (only available on the
FSK network).
Keyboard is locked.
The bell is disabled.
Indicates the status of the battery.
More than 2 handsets in use:
In case more than 2 handsets have
been registered with your phone,
you need to enter the number of the
desired handset (of press key 9 to call
all handsets).
More than 2 handsets in use:
In case more than 2 handsets have
been registered with your phone,
you need to enter the number of the
desired handset (of press key 9 to call
all handsets).
Conference:
As soon as the called handset an-
swers, press the key * (star) during
2 seconds; the outside line is now
included.
Illuminates when u can
show more numbers or
functions in the display
with the keys and and .
The following symbols are:
connected to the key :
Illuminates when u can
open the menu with the
key .
Whenyoupressthekey
,youconrmtheinput
or choice.
The following symbols are
connected to the key :
Illuminates when can make
an intercom call with the
key .
Whenyoupressthekey
now, you will go one
step back in the menu.
Whenthisiconilluminates,
you can delete the input
with the key . If this
icon illuminates during a
phone call, you can disable
the microphone with the
key .
or illuminates when
the number left or right
is longer than can be
displayed on the display.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Profoon pdx 1140 3 handsets wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Profoon pdx 1140 3 handsets

Profoon pdx 1140 3 handsets Bedienungsanleitung - Holländisch - 2 seiten

Profoon pdx 1140 3 handsets Bedienungsanleitung - Holländisch - 20 seiten

Profoon pdx 1140 3 handsets Bedienungsanleitung - Französisch - 2 seiten

Profoon pdx 1140 3 handsets Bedienungsanleitung - Französisch - 20 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info