Bedienungsanleitung Protool PLP 350 E (Seite 9 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490713

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Cutting blades

Operating the electric tool for

a first time

Remaining risks

Lateral guide roller

9. Keep hands away from the chip discharge

channel. If the channel is blocked, first the electric

tool must be switched off and allowed to come to a

complete standstill. After that, the chips may be

removed.

10. Secure work in a safe position with enough support

for a workpiece and the electric tool.

11. Whenever possible, the electric tool should be

connected to the mains via a fault current circuit

breaker (Fl) or a PRCD safety device.

12. This electric tool is not intended for stationary use.

13. The dust originating from planing wood is

hazardous to health. Connect the dust extraction

adapter and wear a dust mask when working with

the electric planer.

14. Turn or exchange blunt knives in good time, the

risk of kickback is otherwise increased.

15. After planing is finished, only put the planer aside

after the cutting head has come to a complete

standstill.

16. Damaged power supply cords must be replaced

immediately by a specialist.

17. Unauthorized use of this product anyway may lead

to a personal injury.

18. Repairs shall be carried out by the qualified

personnel only.

19. Use only the original spare parts.

20. Use safety glasses and ear protection.

21. Use only the original cutting heads identical to the

one supplied with the electric tool.

Even when the electric tool is used properly and all the

relevant safety measures are followed, the following

remaining risks can still occur due to the design of the

electric tool required for the intended working

operations:

- contact with the cutting blades during rundown;

- clothing can be caught by the rotating parts;

- hazards invited by the flexible supply cord;

- hazards invited by the harmful dust when using the

planer for a long time without a dust extractor.

- Check if the data on the nameplate correspond with

the actual voltage of the power supply. The electric

tools with rated voltage 230 V may be also

connected to 220 V. Fusing for 230 V: 16 A slow-

action fuse or equivalent automatic circuit breaker.

- The planer is equipped with the overload cut-out and

LED overload indicator. The overload cut-out

protects the motor against excessive overloading.

- Use only extension cords with a cross section of

3 x 2,5 mm , max. 50 m length. When the electric

tool is used outdoors, use only extension cords

intended for outdoor use and so marked.

- Connection to a standby unit or generator: minimum

power 5 kVA / 230 V, 50 Hz.

- There must be no metal particles on the surface of

the workpiece to be planed. For secure guidance,

the planer is equipped with three handles. Planing

depth is adjustable by means of the swiveling front

handle (5) and the value of adjusted planing depth

may be read on the scale (6) on the side wall of the

planer.

- Attach the supplied chip deflector (12) in front of the

planer on the chip discharge channel (11) and fasten

it with the two star-shaped fixing knobs (13).

- The incorporated soft-start/brake electronic circuit

“SSB electronic” provides for soft starting when the

electric tool is switched on, as well as short rundown

time of approx. 5 s when the electric tool is switched

off.

- When working with the planer, place the front

adjustable shoe (7) onto the workpiece and switch

the motor on, using the switch (2) with the lock-off

button (4) depressed simultaneously. As soon as the

cutting head comes in contact with the workpiece,

guide the planer with constant feed speed, applying

light pressure.

- When planing for a long time with the maximum

planing depth 2,5 mm adjusted and maximum

planing width 350 mm utilized, the LED overload

indicator (24) is to be observed to make sure that the

electric tool is not overloaded - the LED light

intensity increases with overload and the cut-out is

triggered after certain overload rate is achieved. The

electric tool can be started again only after the mains

switch (2) has been released and pressed again.

When intense chip generation is anticipated, there is

advisable to work without the chip deflector (12)

attached.

- In closed rooms, this electric tool may only be

operated with a dust extraction device connected.

When the maximum planing width of 350 mm is to be

utilized, there is possible to use the included guide

roller (9) which rests on the base plate right to the

switch; if required, the guide roller may pulled off with a

light jerk and inserted into the bore on the left side of

the base plate of the planer. When the job is finished,

pull the roller from its operating position and put it back

to the fixture on the base plate.

The cutting head (15) is fitted with the pair of special

reversible blades (16) which cannot be resharpened but

may be reversed once. Blunt blades reduce quality of

the work and increase the risk of kickback. Therefore

they must be turned or replaced in good time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool PLP 350 E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info