572627

Pulsar Digisight LRF N870 Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/50
Nächste Seite
6
7
DESCRIPTION
The Digisight LRF N850/N870 riflescope is designed for observation and
shooting in twilight or nighttime. In complete darkness (no stars or the Moon) use
of the built-in IR (or laser) Illuminator with 780nm wavelength (visible range) or
915nm wavelength (invisible range) is highly recommended. The riflescope is
equipped with a built-in multifunctional rangefinder with a working measuring
range of 400 metres. Your riflescope is a versatile device designed for a wide
range of professional and amateur applications such as hunting, sports
shooting, night video recording and observation.
GUIDELINES FOR OPERATION
The riflescope has been designed for long-term use. To ensure long
performance, please adhere to the following:
Before use make sure that you have installed and fixed the mount according
to the instructions of the section “Installation of mount” (section 9 “Operation”).
Store with the lens cap on in the carrying case.
Switch off the scope after use.
The riflescope cannot be submerged in water.
Attempts to disassemble or repair the scope will void the warranty!
Clean the scope's optical surfaces only if necessary, and use caution. First,
remove (by blowing with a blower brush or canned air) any dust or sand particles.
Then proceed to clean by using camera/lens cleaning equipment approved for
use with multicoated lenses. Do not pour the solution directly onto the lens!
The riflescope can be used in various operating temperatures. However, if it
has been brought indoors from cold temperatures, do not turn it on for 3 to 4
hours. This will prevent external optical surfaces from fogging.
If the scope is unable to mount onto the rifle securely, or you have doubts
about the mounting system, see a qualified gunsmith. Using the weapon with a
poorly mounted scope can lead to inaccurate target shooting!
To ensure reliable performance, it is recommended to carry out regular
technical inspections of the unit.
Do not leave batteries in the unit if it is not going to be used for an extended
period.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
INSTALLATION OF BATTERIES
Unscrew and remove the battery cover from the battery compartment (15).
Install four AA batteries according to the marking on the battery compartment cap.
Replace and screw back the battery cover tightly.
Battery charge level is displayed on the status bar ( ).
In case of complete battery discharge, a red icon is flashing on the status
bar and in the centre of the display.
Note: to ensure long and reliable operation it is recommended that you use
quality rechargeable batteries with a capacity of at least 2500 mAh. Please do
not use batteries of different types or batteries with various charge levels.
EXTERNAL POWER SUPPLY
The riflescope can be powered with an external DC power supply (2.1mm pin)
with stabilized voltage ranging from V to 15V (max. consumption power 3W) or 9
a 12V vehicle socket.
External power supply (AC/DC) is to be connected to “Power” (10) jack
located on the right side of the riflescope.
Note: central pin of the power supply that you connect to the “power” jack of the
riflescope, must have marking “+”. The power supply may have marking .
Connection of an external power supply (icon on the status bar)
automatically cuts off power supply from batteries.
External power supply DOES NOT charge the batteries in the riflescope!
Attention! We suggest that you use battery packs EPS3 or EPS5 ensuring from
9 to 20 hours of continuous operation.
OPERATION
Installation of mount
Before using the riflescope you need to install the mount.
The riflescope can be used with various mount types such as Weaver, Euro-
prism, Los, MAK adapter etc. that allow the scope to be installed on different
types of rifles.
The mounting holes in the base of the riflescope enable the mount to be
installed in one of the multiple positions. The choice of the mounting position
helps the user to ensure the correct eye relief depending on the rifle type.
Attach the mount to the base of the riflescope using a hex-nut wrench and
screws (see installation scheme on page 5).
.Install the scope on the rifle and check if the position is suitable for you
If you are happy with its position, remove the scope, unscrew the screws
halfway, apply some thread sealant onto the thread of the screws and tighten
them fully (do not overtighten). Let the sealant dry for a while.
The riflescope is ready to be installed on a rifle and to be zeroed.
After first installation of your riflescope on a rifle, please follow instructions in
the section “Zeroing”.
Note: Please check that your riflescope is duly zeroed after changing a mount.
Starting the scope and image setup
Install the batteries according to the instructions in Section 7 “Installation of
batteries” or connect an external power supply.
Open the lens cap (2).
Turn on the riflescope turning the selector switch (3) to the “ON” position –
within a couple of seconds the display will light up.
Adjust the sharpness of onscreen symbols with the eyepiece adjustment
ring (4). After this adjustment no further dioptre adjustment should be required,
regardless of distance or other factors.
To adjust the display brightness, rotate the controller (7). Brightness level
from 0 to 20 is shown next to the icon in the upper part of the display and then
on the status bar.
Press the controller (7) to switch to display contrast setup mode. Contrast
level from 0 to 20 is shown next to the icon in the upper part of the display and
then on the status bar.
… 5 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pulsar Digisight LRF N870 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info