491304
4
Zoom out
Zoom in
Vorherige Seite
1/25
Nächste Seite
6
ENGLISH
7
OFF: The unit is permanently switched on.
ON: The unit switches on automatically, if a music signal is received and auto-
matically switches to stand-by mode after approximately 15 minutes, if no
music signal is received.
Units with POWER switch for stand-by only:
The switch operates as follows:
ON: The unit is permanently switched on.
AUTO: The unit switches on automatically, if a music signal is received and auto-
matically switches to stand-by mode after approximately 15 minutes, if no
music signal is received.
OFF: The functions are switched off.
Units with POWER switch for mains only:
If the mains POWER switch is in OFF position, the unit is turned off completely.
If the mains POWER switch is in ON position, the unit is in automatic mode. I.e. if a music
signal is received, the unit switches from stand-by mode to operation mode (ON) and switches
back to stand-by mode, if no music signal is received for approximately 20 minutes.
Connecting up
Before connecting up the subwoofer to your hi-fi or surround system, make sure that the unit
and all system components are switched off, i.e. the pilot lights should all be off.
Connection variant no. 1
(Subwoofer/satellite system for hi-fi and surround)
First take one of the 3m loudspeaker cables supplied with your subwoofer and connect it
to the left-hand speaker output of the amplifier and the left-hand input (HIGH LEVEL) of the
subwoofer. The red „+“ terminal of the amplifier must be wired to the red „+“ terminal of the
subwoofer; the amplifier’s black „-“ terminal must be wired to the black „-“ terminal of the sub
-
woofer. The „+“ line is always coloured red or marked accordingly on speaker cables. Now
repeat the procedure with the second loudspeaker cable to connect the amplifier’s right-hand
speaker output with the subwoofer’s right-hand input. Here too, please take particular care
to ensure that the cables are connected up with the correct polarity, i.e. the red „+“ terminal
of the subwoofer connected to the red „+“ terminal of the amplifier, the black „-“ terminals
connected to each other likewise. By doing so, you will avoid considerable impairment of the
sound as a result of incorrect polarity.
Having connected up your subwoofer at the front-speaker outputs of the digital surround
sound amplifier as shown above, you must now configure the amplifier's bass management
as follows:
Front: large
Subwoofer: no
Centre, rear: large /small (depending on size)
Connection variant no. 1
(Differences of models cause a different position of the operating elements.)
OFF AUTO ON
POWER
1
POWER
ON
OFF
+ RIGHT -
- LEFT +
- + - +
+ RIGHT -
- LEFT +
B
A
POWERPHASE
LOW LEVEL
INPUT
L
R
STANDBY
OFF
ON
0∞
180∞
R LRL
-
+
+
-
HIGH LEVEL
OUTPUT
HIGH LEVEL
INPUT
-3
3
d
2-14
FREQUENCYVOLUME
150
0 dB
-7
50
100 Hz
65
80
120
135
SUBWOOFER
LOUDSPEAKER
AMPLIFIER
LOUDSPEAKER
BDA Subwoofer 11.2006.indd 6-7 16.11.2006 13:28:00 Uhr
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Quadral algemeen wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info