698697
7
Zoom out
Zoom in
Vorherige Seite
1/25
Nächste Seite
12
EN
13
SPECIFICATIONS
A10S
Input sensitivity for 1W @8ohms -16,3 dBV
Input impedance 47kOhm
Voltage gain 38dB
Maximum input voltage 6V
Volume adjustment range 100dB
Balance adjustment range +/-6dB
Adjustment accuracy 0.1dB
Channel balance <0,05dB
Maximum voltage at speaker output 48V
Minimum speaker impedance 2.5 Ohm
Output power at 8 ohms 100W
Output power at 4 ohms 180W
Frequency response 1Hz-110kHz(-3dB)
Harmonic distortion <0.03%
Signal-to-noise ratio 75dB unweighted
Mains power connection 115V/230V switch
Power consumption in normal mode 15W
Power consumption at max volume 600W
Power consumption in standby mode <0,5W
Inputs 3 RCA
1 Line XLR
2 TosLink
1 SPDIF
1 USB
Speaker outputs 1 pair
Dimensions
Width including wooden sides 453 mm
Height including feet 130 mm
Depth with speaker terminals 345 mm
Weight 13.86Kg
INSTALLING
1. Select the correct voltage required on the back of the unit amplifier that matches the voltage coming
from the mains supply. Use the power cable supplied in the package to connect the equipment up to the
mains supply.
2. Check that the unit is switched off.
3. Connect up the auxiliary units that you want to use to the equipment‘s inputs. (RCA 1-3, TosLink, SPDIF,
USB) right channel = red / left channel = white or the symmetric analog XLR inputs can be used with
any compatible signal source.
(XLR pin assignments: Pin 1= ground; Pin 2 = plus / signal; Pin 3 = minus)
4. The screw terminals at the back are used for the speaker connections.
5. (See back of the equipment: right channel = 1 / left channel = 7). You must also ensure that the plus
and minus connections on the amplifier concur with the plus and minus connections on the speakers in
order to prevent polarity reversal.
6. Now switch your amplifier on.
Switch the mains switch (12) into the ON position on the back. The standby LED on the front will come
on.
7. Now press the multifunction knob (2) on the front or the button (2) on the remote control to start your
equipment.
Note:
As your A10S uses a special power-saving standby circuit, you can always switch on / off during normal
operation using the multifunction knob on the unit or the RC-3 remote control.
The RC-3 remote control makes it easier for you to change your settings.
Mute (button 2)
Balance setting (buttons 14 + 15)
Input settings for all jacks (button 3 + 4)
Example: Input settings
Select the signal source using buttons 11 (-) or 12 (+), then press button 22 (Prog.) and use the volume but-
tons (3 + 4) to set the desired input volume. To save, press button 22 (Prog.) again.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Quadral AURUM A10S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info