Bedienungsanleitung Quadral Aurum C8 (Seite 5 von 19) (Deutsch, Englisch, Französisch, Spanisch)

698711

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

INSTALLING

1. Use the power cable supplied in the package to connect the equipment up to the mains supply.

2. Check that the unit is switched off.

3. Connect up the CD player to the amplifier inputs.

(CD-Output) right channel = red / left channel = white

4. Now switch your CD player on.

Switch the mains switch (3) into the ON position on the back.

The standby LED on the front will come on.

7. Now press the On / Standby button (10) on the front or the button (2) on the remote control to start

your equipment.

Note:

As your C8 uses a special power-saving standby circuit, you can always switch on / off during normal

operation using the On / Standby button on the unit or the RC-2 remote control.

Mute (button 3)

Balance setting (buttons 6 & 7)

Multilevel display brilliance setting (button 15)

Input level setting for all inputs (button 14)

Example: Input level setting

Use buttons 8 (-) or 9 (+) to select the signal source and then press button 14 (Prog.) and use the volume

buttons (4 & 5) to set up the input volume to suit yourself. Press button 14 (Prog.) once again to save the

settings.

AMBIENT CONDITIONS

The remote control has a range of up to 6 m and works without any problems from a radiating angle of up

to 30° in relation to the front of the equipment. Dust on the transmitter or dirt on the receiving sensor and

operating it in the vicinity of fluorescent lights might reduce the range. A direct line-of-sight connection

between the transmitter and the receiver is needed.

Notes about the removal and the correct environmentally-friendly disposal of old batteries

The symbol shown here can be found on the equipment‘s enclosure, the packaging as well as in the doc-

uments or the operating manual. It tells you that batteries provided with the equipment as well as those

supplied with or fitted in other units must never be disposed of in household waste. They must be disposed

of in an environmentally-friendly way (in compliance with the local regulations or European Directives

2002/96/EU and 2006/66/EU).

You should find out where the nearest collection point for electronic scrap is or where the recycling site is.

Correct disposal of the equipment and the batteries will help to preserve our resources and prevent phys-

ical and environmental damage. The battery (CR2032) supplied with the remote control contains lithium

and it must be disposed of in an environmentally-friendly way as described above.

Proceed as described in the following section to replace or remove the battery fitted in the remote control.

1. Undo the screw in the cover underneath the remote control and then remove the cover.

2. Remove the battery by sliding it out of its holder.

3. You must ensure that the new battery‘s polarity is correct when you fit the new one! The side of the

battery marked with (+) must point upwards so that it makes contact with the part of the holder

marked with (+).

4. Refit the cover and use the screw to secure it in place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadral Aurum C8 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info