Bedienungsanleitung Radical Audio RA163.3 (Seite 5 von 24) (Deutsch, Englisch)

490215

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

INSTALLATION CONSIDERATIONS

GENERAL SUGGESTIONS

a Make sure you have enough high quality speaker wire at hand, to reach all the drivers

and crossovers from their intended mounting locations! The preferable cross-section is

2x2.5mm

. Please consider that for quality reasons, only the tweeter and midrange

extension leads are provided with the set content. All other speaker wires - especially

those to connect the mid/woofers and the amplifier to the crossover(s) - must be

purchased separately from your Radical Audio dealer.

s Before you attempt to mount the tweeter(s), midrange unit(s) or mid/woofer(s) in the

doors of a vehicle, check the available mounting depth! Always make sure the speakers

or crossovers do not interfere with either the door or window operation.

d Before you start any wiring work, speaker mounting etc, disconnect the negative power

cable lead from the battery! For your safety…

f Never run speaker wires over or through sharp edges. Use rubber grommets to protect

wires routed through metal.

MOUNTING LOCATION

A solid front stage with good imaging is one of the most difficult things to achieve in a

vehicle! Mostly because the speakers are placed where they will fit easily, as opposed

where they can perform the best. In most cases, the factory cut-outs - i.e. in the front

doors of a vehicle - offer a stable and convenient mounting platform for the mid/woofers.

In some cases you will need to purchase car specific plastic adaptors for proper mounting

of Euro-DIN style mid/woofers to the factory speaker cut-outs in the front doors.

Concerning the tweeters and the midrange units, the chosen mounting location will defini-

tely exhibit a profound and direct effect on the sound staging of your component speaker

system. Therefore, after mounting the mid/woofers and crossovers - try to mount the

midrange units as far to the front and as high as possible in the front doors, while the

tweeters should be located relatively close to the midrange units, preferably in the window

triangles or the A-pillars. Before the tweeters are mounted, it is recommended to fix them

with carpet tape - in several potential locations - to determine the best sounding location.

Of course this must be attempted, BEFORE YOU CUT YOUR PANELS!

SOME MOUNTING GUIDELINES:

a Place the tweeters and midrange units where they have a direct - unobstructed - path

to the listening area. The best visual location may not be the best sounding one!

s Listen to the system with both tweeters connected to the crossovers in phase

(࿜ to ࿜, ࿛ to ࿛) AND reversed, before making a final decision!

d Be sure to use the supplied foam gaskets when mounting the mid/woofers. These

gaskets enable an airtight seal between the mid/woofer mounting rim and the speaker

mounting hole, important to obtain the maximum dynamic range in the lower transmis-

sion band!

f The installation of your component set is carried out best, following this logical

sequence: Removal of Factory Speakers z Wire Routing z Installation of the

Mid/Woofers z Installation of the Midrange Units z Mounting the Crossovers z

Mounting the Tweeters

RA163.3 Manual 16.07.2002 18:38 Uhr Seite 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Radical Audio RA163.3 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info