500597
5
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
5
4. SMALL DESCRIPTION
This controller (Receiver + Master) with the main zone programmer are a complete package to manage all
component of your water floor heating and cooling installation.
You could control different type of installations:
Installation1: Heating only.
Installation2: Cooling Only
Installation3: Separate systems (Boiler and water chillers) or slave heat pump.
Installation4: Reversible Heat pump (manual or automatic)
Installation5: Reversible Heat pump (without Heat & Cool information and control)
In case of cooling function is used, you could control the residual humidity in the house by:
The special input on the receiver which can be use for a NTC or Humidity sensor mounting on incoming pipe of
the manifold or a special humidity sensor (see the wiring diagram).
5. LED EXPLANATION
Keyboards:
Validation key (OK)
Plus key (+)
Minus key (-)
Navigation key left (◄)
Navigation key right (►)
Display:
Humidity drier output activated.
1. Comfort mode indicator.
2. Reduced mode indicator.
3. Anti-freeze mode indicator.
4. Heating mode indicator (blinks when operating).
5. Cooling mode indicator (blinks when operating).
6. Room temperatures indicator.
7. Current zone or Room temperature if 7 displayed.
8. Radio frequency graphic.
9. Setting temperature required by the zone thermostat
Or floor temperature if floor sensor is used and 7 displayed.
Special displaying:
FL.l: Indicate that the zone thermostat is in « Floor Lower limitation mode »
FL.h: Indicate that the zone thermostat is in « Floor upper limitation mode »
(Only available if floor sensor is connected)
OFF: Indicate that the thermostat is stopped.
LED 1: Red => Heating demand indication
Red blinking => Heat & cool sensor error
Green => Cooling demand indication
Green Blinking => Humidity detection (Humidity drier is activated)
Off => System in standby
LED 2: Orange => Pump running indicator
LED 3 to 6 (or Led 14 with 2 slaves):
Green Flash: => indicates a correct radio reception on zone.
Green blinking: => - In normal functioning if you press one key indicates the current zone or group zone
selected.
Red: =>Indicates that the zone is activated (Water circulation on this circuit)
Red blinking: Indicates that this zone is in radio reception alarm. The RF thermostat radio signal has
been lost.
(See Radio reception alarm section).
LED1 ------------------------------------------------------------------ LED14
8
4
2
6
1
10
7
5
3
9
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Radson 51055 - SLAVE RF wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info