Bedienungsanleitung Radson Minuterie (Seite 2 von 10) (Englisch, Holländisch, Französisch)

500581

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

LAUNCHING A MANUAL BOOST

This function enables you to increase the tempera-

ture in your room rapidly and/or to dry your towels

for 2 hours. The device’s thermostat will not be in use

over this period.

The device will function normally again [the thermo-

stat will be used to regulate room temperature] as

soon as the timer stops.

•

Press the OK/Boost button: when it is released, the

light [5] will ﬂash once to show that the manual

Boost has been registered, and the receiver light [1]

will ﬂash red.

NOTE:

You can stop the Boost at any time by pressing the

button again. The receiver light [1] will stop ﬂashing.

PROGRAMMING DAILY BOOSTS

The infrared room thermostat enables you to

programme 2 daily Boosts P1 and P2.

Programming a daily P1 Boost

• Turn the cursor [8] to P1.

• At the desired time, press the OK/Boost button for

three seconds to save the P1 cycle:

- The light [5] will ﬂash twice brieﬂy to indicate

that the daily Boost has been registered, and the

receiver light [1] will ﬂash red.

- The Boost will start immediately for 2 hours and

will repeat after 23 hours and 15 minutes, and

then every 24 hours.

Example: The ﬁrst morning at 7 o’clock, press the OK/

Boost button for three seconds. The next day, and on

subsequent days, the appliance will switch on at 6.15

for 2 hours. At the end of the Boost, the device goes

back to comfort mode.

Programming a second daily P2 Boost

• Turn the cursor [8] to P1+P2.

• Proceed as for programming P1 Boost .

- The second 2 hour Boost will start immediately

and will repeat after 13 hours and 15 minutes,

and then every 24 hours.

NOTE: You can stop the timer at an time by pressing

the OK/Boost button brieﬂy.

Changing a programmed Boost

• Turn the cursor [8] to the chosen programme and,

at the desired time, press the OK/Boost button

for 3 seconds: the new cycle will be saved and the

previous one will be erased.

NOTE: 2 quick ﬂashes indicate that a P1 Boost [or

P2 Boost] programme has already been saved when

going into P1 mode [or P1+P2 mode].

RETURNING TO FACTORY SETTINGS

This will erase all programmes and restore the default

factory settings.

• Turn the cursor [8] to

mode then press down for

at least 10 seconds:

- The light [5] will ﬂash twice to indicate that the

re-set has been registered.

- P1 and P2 programmes will be erased.

CALIBRATING THE THERMOSTAT

It is normal for there to

be a 1 to 2°C difference

between the temperature

displayed on the emitter

and that measured by a

thermometer.

If you wish to synchronize

these two values, let your

thermostat regulate the

temperature for at least

an hour and then proceed

as follows:

Example: you have set

your thermostat to

21°C. After an hour of

regulating the tempera-

ture, the thermometer is

displaying 23°C.

• Remove the temperature knob, taking care not to

turn it at the same time.

• Remove the knob’s central notched axle [with a

small pair of pincers] and put the axle back in the

thermostat pivot, without making it move round.

• Then place the knob back so as the temperature

you have measured is the same as that shown on

the thermostat dial.

SETTING A MAXIMUM TEMPERATURE

FOR THE THERMOSTAT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Radson Minuterie Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info