Bedienungsanleitung Redmond RI-C222-E (Seite 5 von 144) (Alle Sprachen)

659488

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

GBR

RI-C222-E

Steam ironing

The most efcient steam ironing can be achieved in • • or • • • temperature modes.

Turn the steam output control dial into the required position. If the dial is in position the

steam feature is disabled (use the mode for dry ironing). Turn the steam output control dial

in direction towards position to increase the steam output.

Plug in the iron. Heating indicator on the housing will light up to indicate the heating. Once

the soleplate reaches the required temperature the heating indicator will go out, indicating

that the iron is ready to use.

NOTE! Constant steam is only generated when the iron is in horizontal position and set to high

temperature. If the steam feature is enabled (the steam output control dial is not in position)

and the temperature setting is too low, water may drip from the soleplate.

Steam Shot

The Steam Shot feature is used to eliminate stubborn wrinkles. The feature can be used

during steam ironing when the heating indicator on the housing is out. If the heating indi-

cator is lit, wait for the soleplate to reach the selected temperature before using the Steam

Shot feature. The Steam output control dial must not be in position.

Briey press the Steam Shot button during ironing for extra steam. Allow an interval of 2-3

seconds between the shots. Steam Shot feature can be used for vertical steaming.

NOTE! When the iron is set to low temperature (• position) water may drip from the soleplate,

the Steam Shot feature may not be applicable.

Vertical steam

The REDMOND RI-C222-E Steam Iron can be used in an upright position to remove wrinkles from

hanging drapes, curtains, tulle, as well as dress clothes without taking them off the hangers.

1. Turn the steam output control dial into position.

2. Turn the temperature control dial into “Max” position.

3. Wait until the soleplate reaches the required temperature (the heating indicator goes out).

4. Hold the iron vertically with the soleplate facing the garment. To avoid burning deli-

cate fabrics hold the iron a few centimeters away from the garment.

5. Move the iron from top to bottom briey pressing the Steam Shot button. Return to

horizontal position every fth time you press the button.

6. If heating indicator lights up, stop steaming and wait for the soleplate to reach the

required temperature. Resume the steaming after the heating indicator goes out.

CAUTION! The iron generates high temperature steam! Do not touch steam to prevent burning.

Never iron clothes on the body!

Dry ironing

You can use the iron for dry ironing even if the water tank is full. However, if using the

feature for a long period of time do not ll the tank with too much water.

1. Turn steam output control dial into position.

2. Turn the temperature control dial to select the temperature appropriate for your fabric.

3. After soleplate reaches selected temperature and heating indicator goes out, the iron

is ready to use.

Water spray feature

Use the water spray feature to dampen hard-to-iron fabrics, remove stubborn wrinkles, and to

iron difcult areas such as collars, etc. Press the water spray button to dampen the fabric:

• slowly and smoothly for a dense spray

• quickly for vaporized spray

The feature can be used as often as required from any temperature mode, as long as there

is enough water in the water tank.

Auto shut-off feature

The auto shut-off feature ensures safety and reduces energy consumption. The iron auto-

matically shuts off when left unattended:

• after 30 seconds of inactivity in horizontal position or on its side (tipped over)

• after 8 minutes of inactivity in vertical position

After the auto shut-off occurs the soleplate stops heating, audible signal is heard, the auto shut-off

indicator on the handle starts ashing. To continue ironing take the iron by the handle. The auto

shut-off indicator will stop ashing, the heating indicator will light up. Once the soleplate reaches

the required temperature the heating indicator will go out, indicating that the iron is ready to use.

Anti-drip feature

The anti-drip feature prevents water from dripping onto fabric and enables to iron even the

most delicate garments. Use low temperature setting (• position) to iron delicate fabrics.

After each use

Turn the temperature control dial into “Min” position and the steam output control dial into

position. Unplug the iron from electrical outlet. Open the water tank cap and gently shake

the iron above the sink to empty the tank. Place the iron into a vertical position.

Wait for the soleplate to cool down thoroughly. Wind the cord around the heel of the iron.

Store in vertical position.

Fabric Ironing Chart

Symbol of the

temperature

mode

Temperature

control dial

position

Fabric Ironing recommendations

•

SYNTHETICS

Acrylic

Iron carefully. Do not use steam iron-

ing to prevent water from dripping

out of soleplate and staining the

fabric

Polyamide (cap-

ron, nylon)

Polyurethane

Acetate

Iron on reverse side, fabric cannot

withstand high heat. Acetate dries fast

and needs little ironing

Polyester Iron using a damp press cloth

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Redmond RI-C222-E Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info