Bedienungsanleitung Reflexion CLR-2970KCD (Seite 4 von 19) (Deutsch, Englisch, Französisch, Italienisch)

592112

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

EnglishEnglish

3 4

sound when reach the alarm 2 time.

- or when alarm 1 sound then PRESS POWER/ALARM RESET button directly, it will

switch to alarm 2 fuction.

- by keeping the NEXT/FF/TUN+ button (12) or PREVIOUS/FB/TUN- button (16)

pressed, the time runs forwards or backwards at high speed.

Normal condition

Press POWER/ALARM RESET button (1) to turn on the LCD back light and

switch to normal condition.

RADIO OPERATION

In normal condition, press TUNER button (11) to enter radio function.

- press VOL+ (17)/VOL- (18) to turn UP/ DOWN the volume, “l up/ l dn” will be

shown on

the LCD.

- repeat press STOP/BAND button (14) to select the station of FM/AM.

- press NEXT/FF/TUN+ button (12) or PREVIOUS/FB/TUN- button (16) to receive

the frequcecy of the station.

Press NEXT/FF/TUN+ button (12) or PREVIOUS/FB/TUN- button (16) once, the

change of FM frequcncy is 100Khz, and the change of am frequency is 9Khz.

PressNEXT/FF/TUN+ button (12) orPREVIOUS/FB/TUN- button (16) for 2 seconds,

it will switch to automatically search the station function.

Antenna

For FM reception there is a wire FM antenna at the rear of the unit. Extend the antenna and

move it around to obtain the best reception.

For MW reception the signals are picked up through a wire antenna. Your may have to orient

the wire to obtain the best reception.

PROGRAM RADIO OPERATION

- In radio condition, press NEXT/FF/TUN+ button (12) or PREVIOUS/FB/TUN-

button (16) to select the station which to be programed.

- press PROG/C-ADJ button (15) to enter program function. LCD will display

“MEMORY” and “P”.

- press REPEAT/M-RECALL (9) button to select the required station number, then

press PROG/C-ADJ (15) button to confirm the station number.

- repeat the above operations can program 30 stations. there are 15 programs in

the FM/AM separately.

- when turn on the radio, press REPEAT/M-RECALL button (9) you can repeat

index the station which stored in the program.

MOUNTING

1. Choose a spot near an electrical outlet.

2. Rotate the 4 mounting adapters to choose the apposite distance between the unit

and the spot.

3. Mark the mounting position, drill 4 holes x diam. 6 mm.

4. Install the mounting adapter on the spot.

Note : Fixings used to mount this unit must be suitable for construction material.

POWERSUPPLY

This unit operates from a main supply of 230V ~ 50Hz. Connect the AC power cord to the AC

household main outlet. Ensure that the voltage is as indicated on the rating plate on the rear

of the unit.

- mains plug is used as the disconnect device, the disconnect device shall

remain readily operable. always remember to disconnect the power cord from

the main supply before disconnecting the lead from the unit.

- when connect to the main power, the initial state of the unit will display “0:00”.

- reset both the correct time and the required alarm time for proper operation.

SETTINGTHECORRECTTIME

Time setting on the unit should be done in POWER OFF mode only.

Clock setting:

- press and hold the prog/c-adj button (15).

- at the same time press NEXT/FF/TUN+ (12) button or PREVIOUS/FB/TUN- button

(16) separately to set the hour or min time.

Alarm setting:

- slide the function switch (AUTO-CD-TUNER-BUZZER) (19) to BUZZER position.

- press disp button (4) to choose al1 or al2 setting, LCD will display al1 or al2.

- the first time press disp (4) is al1 function, then set the alarm time, the operation

is same as clock setting. after setting the alarm time press ALARM/ON/OFF button

(5) to store the time.

- then set the alarm 2. the alarm2 setting is same as alarm 1. When the time is the

same as the alarm 1 time, the buzz trump sounds. press the snooze button (8) to

turn off the alarm 1 sound temporarily. This time will cancel the alarm 2 function if

not press POWER/ ALARM RESET button (1). After 9 minutes the alarm 1 sound

again.

- If alarm 1 sounds press the snooze button (8) then continue press the POWER/

ALARM set button (1) alarm 1 will not sounds after 9 minutes. But the alarm 2 will

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Reflexion CLR-2970KCD Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info