Bedienungsanleitung REL Acoustics Q serie (Seite 18 von 25) (Englisch)

601224

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

REL Acoustics ‘Q’ range User manual

Note: As the Q-series crossover adjustment uses a single variable control, use the closest

correlating position to any of the crossover settings noted above for ST series models.

Ultimately, as with the click stops of the ST range, simply bring gain and then crossover up

until excess output is achieved, then back down a soft-click or two.

Hint: There is a tendency among audiophiles to set the crossover point too high and the gain

too low when first learning how to integrate a REL with the system, the fear being one of

overwhelming the main speakers with bass. But in doing so, the resulting set-up will be

lacking in bass depth and dynamics. The proper crossover point and gain setting will

increase overall dynamics, allow for extended bass frequencies, and improve soundstage

properties.

Note, gain must be adjusted in conjunction with crossover changes. In general, when

selecting a lower crossover point, more gain may need to be applied.

Theatre and Film Applications: For Dolby Digital AC-3 or other 5.1 theatre systems, once the

standard set-up for two-channel outlined above is complete, the LFE output from the processor or

receiver should be connected to the low-level input and appropriate gain adjustments made. It may

be necessary to take the crossover out of the low-level input using the “mode” switch if extra upper

bass output is called for. Keep phase consistent with what was selected during high-level set-up by

simply choosing the corresponding setting (1 = 2, 3 = 4). For this configuration, you must set the

processor to the “large” or “full range” setting for the left and right speakers in order for the REL to

receive the bass signal via the high-level cable. In this configuration, the REL provides support for

both the left and right speakers for two-channel listening, and support for the LFE when movies are

playing. Most processors will allow you to defeat the subwoofer output when listening in the two-

channel mode. The effect of this set-up is one of greatly increased dynamics in the mid-bass range,

no bass bloat, and a greater degree of space and timing from the Foley effects. For an even greater

sense of space and impact, a second woofer connected in parallel to the centre channel will prove to

be a dramatic improvement as well. And if that is not enough fun, a rear sub, both to support the rear

channel speakers as well as to evenly distribute LFE through the room, truly completes the full-range

sonic picture for state-of-the-art film reproduction. A comprehensive set-up paper for home theatre

will be coming very soon.

Other Tips: Generally speaking, do not use the supplied spikes. RELs work on the principle of the

driver in a high-pressure zone relative to the floor. Spiking the REL will decouple the woofer from the

floor, which will lean out the bass response. If the floor is an older, very “springy” floor, spikes can be

useful in reducing the influence of the REL on the floor. But better yet, a heavy stone slab placed

under the REL will work better. Even if you intend to use the spikes, do NOT insert them until

completion of the set-up process. After which, subtle adjustments to crossover and gain may be

necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REL Acoustics Q serie Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info