Bedienungsanleitung Remington HC5550 (Seite 6 von 9) (Englisch)

490471

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

SHORT TAPERED STYLES – “FLAT TOPS” & SHORT CUTS

Starting with the longest

comb attached (

), cut from the back of the neck to

the crown. Hold the guide comb ﬂat against the head and slowly move the clipper through

the hair, as shown. (PICTURE 1)

Use the same procedure from the lower side to the upper side of the head, as illustrated.

Then cut the hair against the direction in which it grows and level with the sides.

(PICTURE 3)

To give a “ﬂat top” look, the hair on top of the head must be cut over the top of a ﬂat

comb.

Use a closer guide comb to taper the hair down to the neckline as desired.

ENGLISH

STEP 5 – The ﬁnishing touches – PICTURE 5

Use the clipper without an attachment comb for close trimming around the base and sides

of the neck. Use the ear comb guides to get a clean line around each ear. For the required

ear comb guide, angle the clipper and lightly stroke around each ear to the back of the

neck.

To produce a clean straight line at the sideburns, reverse the hair clipper. Place the

reversed clipper at right angles to the head, tips of the blades lightly touching the skin and

then work downwards.

24mm-42

INSTRUCTIONS FOR THE STUBBLE GUIDE COMB (Only for HC5550 & HC5750)

The 1.5mm guide comb is designed to create the perfect 3-day beard look.

Place the flat top of the trimmer comb against the skin.

Slowly slide the trimmer through the beard. Repeat from different direction as necessary.

If hair builds up in the trimmer comb during the trimming process, switch the unit off, pull

off the comb and brush/rinse off.

AUTO BOOST SYSTEM (Only for HC5750)

There are 3 settings for the Auto Boost system: Off, Auto and Boost.

If the clipper is set to Auto it will run at regular power under low load conditions.

When more power is needed, the clipper with automatically sense and provide maximum Boost.

If the clipper is set to Boost, it will run at maximum power at all times.

DUAL BOOST SYSTEM (Only for HC5550)

There are 3 settings for the Dual Boost system: Off, On, Boost.

If the clipper is set to On, it will run at regular power.

If the clipper is set to Boost, it will provide maximum power.

Always work from the back of the head.

Use the longer length comb attachment and set it to 24mm or 27mm

then cut hair on top of the head against the direction in which the hair normally grows.

STEP 4 – Top of the head – PICTURE 4

For longer hair on top, use the longer length comb attachment (24-42mm) to achieve desired style.

HAIR THINNER MECHANISM

Simply adjust the hair thinner mechanism by sliding the button at the top of the hair clipper.

Blending different length areas. Select the proper length guard to blend. Slide out the Texture/Thin out feature.

Textured cut – Slide out the texture/thin out feature with the guard in place to give an all over textured cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remington HC5550 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Remington HC5550

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info