Bedienungsanleitung REMKO RKL220 (Seite 5 von 16) (Englisch)

587563

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Unit functionality

A portable air conditioner works in principle like a refrig-

erator. In a refrigerator, heat is withdrawn from the food

and drinks stored inside it. This heat is expelled to the

surrounding air by means of a heat-exchanger on the

back of the refrigerator.

The portable air conditioner cools the air in the room by

withdrawing heat from it. The heat absorbed is expelled

to the outside and the cooled air is resupplied to the

room where the unit is in operation.

Condensation

During cooling mode, the air that has been sucked in

from the room is cooled until it falls below the dew point

and the steam contained in it condenses on the evapo-

rator surface.

The condensed water drips into the condensation trap 7

attached under the evaporator and, from there, enters

the water tank 8.

The water tank must be emptied from time to time.

Diagram of process

Unit Description

The unit is operated with electric power and has been

designed for universal, fully-automatic, smooth opera-

tion. Its compact design lets it be easily transported and

used almost anywhere.

The device works on the principle of compression. It is

equipped with a closed-loop cooling system, a quiet ra-

dial fan which requires little maintenance and a power

cable with plug.

The fully-automatic control, integrated thermostat,

three-setting fan and water tank with integrated overflow

safety mechanism ensure proper operation of the unit.

This portable air conditioner meets the basic safety and

consumer health requirements outlined in the relevant

EU regulations. It is safe and easy to operate.

How is the air cooled in the room?

In a closed-loop cycle, there is a special medium called

a refrigerant. This refrigerant transports the excess heat

out of the room to be cooled.

At the beginning of the cycle, this refrigerant, in the form

of steam, is sucked in by the compressor 2, com-

pressed and, as a result, becomes very hot.

The heated refrigerant is routed to an exchanger

mechanism, the condensator 3. In the condensator, the

refrigerant steam is cooled by the room in the air until it

condenses. The heat is expelled over the flexible ex-

haust hose to the outside by a fan. 5.

In an injection nozzle, the flow control mechanism 4, the

pressure on the air is decreased and it is routed to an-

other exchanger mechanism, the evaporator 1.

Cold air is actually generated in the evaporator. The liq-

uid refrigerant evaporates, the heat required for this pro-

cess is withdrawn from the air in the room that the fan 6

guides via the evaporator.

The cooled air is resupplied to the room and the cycle

begins again for the refrigerant. The temperature of the

room is gradually lowered through this cyclical process.

Because the cold cycle is a closed-loop, no refrigerant

is lost or consumed.

cold air

room air

warm air

room air

Unit equipment

Handle

Water tank

Air outlet grill

Control panel

Adjustment

lever

Transport

wheels

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKL220 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKL220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info