Bedienungsanleitung REMKO RKL470 (Seite 7 von 16) (Englisch)

587572

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Operating Mode

Cooling

1. Switch the unit on with the "On / Off” button.

2. Set the target temperature using the arrow buttons.

3. Select the fan setting (AUTO, HI, MED or LO) with

the "MODE" button.

Ventilation (circulation)

1. Switch the unit on with the "On / Off” button.

2. Set the FAN operating mode with the "MODE” but-

ton.

3. Please note: in circulation mode, the outdoor unit

can remain in the room. But do not attach the out-

door unit to the indoor unit.

Dehumidifying

Set up the indoor unit and the outdoor unit in the room

to be dehumidified.

1. Make sure that the indoor unit is not drawing in

warm air from the outdoor unit.

2. Do not attach the outdoor unit to the indoor unit.

3. Please note: the condensation which forms during

dehumidifying may not be pumped to the outdoor

unit because otherwise it would be expelled to the

air in the room or would drip out of the outdoor unit.

4. Remove the water tank drainage tube from the back

of the indoor unit from its holder and remove the

sealing cap.

5. Guide the condensation at an incline to a drain or a

container.

Fig. 5

POWER

on / off

TIMER

reset

AUTO

SWING

MODE

set

THERMO

CONTROL

Make sure that the lower edge of the outdoor unit

is 1.8 meters above the lower edge of the indoor

unit.

Make sure that the external container does not

overflow!

This may cause water damage.

10 Operating mode and fan setting display

This display provides information about the operat-

ing mode and the fan setting which have been se-

lected.

11 "DRAIN WATER" display (Water tank full)

When the water tank is full, the "DRAIN WATER" and

"MODE" displays blink and an alarm goes off. The

compressor automatically switches off. After the wa-

ter tank has been emptied and replaced, the unit

switches back to automatic operation.

Information about the water tank:

During normal operation, the water tank will not fill up

because the condensation is pumped out of the tank via

the connecting line to the outdoor unit.

Infrared-remote Control

All settings can also be made using an infrared remote

control (optional with RKL 460).

A description of the button functions (see picture below)

can be found in the “Control panel” section. The remote

control’s range is approximately 5 m.

Power is provided by two 1.5 V AAA batteries. (supplied

with the remote control)

6. Switch the unit on with the On / Off button.

7. Set the unit to the lowest target temperature with the

temperature selector button.

20°C.

8. Using the MODE button, set the lowest fan speed.

LO.

The water tank must be emptied when fixing malfunc-

tions.

Proceed as follows:

1. Remove the water tank drainage tube on the back of

the indoor unit from its holder.

2. Remove the sealing cap from the tube.

3. Collect the water that drains out.

4. Then reinsert the sealing cap into the tube.

5. Replace the tube into its holder.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKL470 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKL470

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info