Bedienungsanleitung REMKO RKL490 DC (Seite 6 von 20) (Englisch)

587574

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

The system can be operated by means of the control panel on the device or via the standard infrared remote

control unit. The functional operation of the buttons among themselves is identical, however, the designation

can vary. The batteries must be correctly inserted before the infrared remote control is used.

Operation

Legend

 "ON / OFF" button

 "MODE" button

(Fan speed – mode)

The fan speed is indicated by

means of LEDs in the selected

modes AUTOHIMEDLO or

circulated air modeFAN.

 LED "COMP. ON"

(Compressor operation)

The controller controls the cool-

ing output by means of switch-

ing the compressor on or off.

Compressor operation is indicat-

ed by means of the LED. If the

LED ﬂashes, the compressor will

be activated in max. 3 mins.

 Button "▼ ▲"

Temperature setting

The desired nominal temperature

can be set with the ▼▲ buttons

in steps of 1°C between 16 and

30°C.

 On and off timer

The timer function can be used

to switch the device on or off

automatically in hourly intervals

("▼▲" buttons) by means of

pressing the "SET" button. The

function can be used to program

the switch-on timer when the

device is off and the switch-off

timer when the device is on, for

up to 24 hours. Both timers can

be deleted by means of pressing

the "RESET" button.

 AUTO SWING button

The direction of the discharged

air via the oscillating ﬁns can be

adjusted to ﬁxed or oscillating

by pressing the "AUTO SWING"

button.

 LED "DRAIN WATER"

If the pump is unable to trans-

port the collected condensate

then this is signalised via an

acoustic alarm in combina-

tion with the ﬂashing "DRAIN

WATER" LED. The device will

be operational again after the

container is emptied by means

of the condensate drain.

 Display

The display shows the set nomi-

nal temperature or the residual

time of a programmed timer.

 Infrared receiver

The device receives the signals

from the infrared remote con-

trol via the sensor.

FAN button

The ventilator speed can be

adjusted by means of pressing

the "FAN" button.

Cooling mode

1. Switch the unit on by means of

the "I / 0" button.

2. Set the temperature selection

switch to the desired nominal

temperature.

3. Select the desired fan mode

to AUTO, HI, MED or LO by

means of the "MODE" button.

Circulated air

1. Switch the unit on by means of

the "I / 0" button.

2. Select FAN mode by means of

the "MODE" button.

The outdoor unit can remain in the

room in circulated air mode.

However, do not hang the outdoor

unit onto the indoor unit.

Dehumidifying mode

Position the indoor unit and the

outdoor unit in the room that is to

be dehumidiﬁed.

1. Ensure that the indoor unit can-

not extract warm air from the

outdoor unit.

2. Do not hang the outdoor unit

onto the indoor unit.

3. Please observe: The condensate

formed during dehumidiﬁca-

tion may not be pumped to the

outdoor unit as otherwise it will

be dissipated back into the air

in the room or may run out of

the outdoor unit.

  



    

Control panel

FAN

TEMP.

ON/OFF

FUZZY

TIMER

MODE

infrared remote control

Infrared transmitter

REMKO RKL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO RKL490 DC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO RKL490 DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info