Bedienungsanleitung Ricatech RMC400 (Seite 4 von 59) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

610897

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

Power Source

1 Plug the AC Adaptor (output 12V 3A) of the unit into appropriate wall outlet

2 Plug the small end of the adapter into the Adaptor Jack on the back of the unit.

General

1 Make sure the unit is plugged in correctly to an AC outlet.

2 Press the POWER button to turn on the unit .

3 Once the power is turned on, press the FUNCTION button to switch between Tuner/CD/Phono/Aux.

When switching between functions, wait one second after pressing the function button before pressing it

again. This gives the unit time to load the correct information for the selected function.

Radio Operation

1 Press the FUNCTION button to set the unit to Tuner mode

2 Press the BAND button to select the desired tuning band (AM/FM).

3 Select the desired radio station by rotating Tuning knob .

4 Adjust the volume to the desired listening level.

Antenna

Antenna: for FM reception, the unit is provided with a FM WIRE ANTENNA , move the wire until the reception is

clear and with no interferences. For AM reception, the unit is provided with a directional build-in ferrite antenna.

Rotate the set to find the position in which the best reception is obtained. Do not connect the EXTERNAL FM

ANTENNA to any outside antenna.

USB Operation

Using the included software and cable, the USB connection allows you record your records onto your computer.

Follow these instructions to use the USB.

1 Insert the enclosed software CD into your computer.

2 Follow the instructions on the computer screen to install the software. If the software does not load

automatically, browse the software CD and open the "Readme.html" file. Follow the instructions on the main

menu.

3 Connect the square end of the cable to the JACK on the back of the unit.

4 Connect the other end to a USB port on your computer.

5 On your computer, open the Record Recording Software.

6 For instructions on operating the Record Recording Software, browse the software CD and open the

README.html .

Turntable Operation

1 Press the FUNCTION button to set the unit to Phono mode.

2 Set the SPEED CONTROL SWITCH to the correct speed (331/3, 45 or 78 rpm) for the selected record.

3 Use the CUE LEVER to raise the tone arm off its rest. Move the tone arm over the record and use the

cue lever to lower it to the point you want the record to start.

4 At the end of the record, the tone arm will return to its rest.

NOTE:The turntable and cassette players both operate in the same mode. Make sure the cassette player is in

STOP mode when listening to a record.

Accessory:ADAPTER FOR 45 RPM

To play the 45rpm record, place the ADAPTER on the spindle.

Playing a Cassette

1 While in Phono mode, press the STOP/EJECT button on the cassette player to open the cassette door.

2 Insert a prerecorded cassette tape into the cassette door.

3 Press the PLAY button to begin play.

4 To stop playback, press the STOP/EJECT button.

5 Press the STOP/EJECT button again to eject the cassette.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ricatech RMC400 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info