Bedienungsanleitung Riho Whirlpool Electronic LCD (Seite 3 von 28) (Englisch)

626525

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Z1209004. 5 GB

Enjoy the RIHO life-style

Whirlpool Electronic LCD user handbook

1.4 Pre-installation actions

The installer must ensure the presence of the following structural facilities among other things:

- Ventilation grid for the motor(s) of at least 100cm².

- A 2nd ventilation grid for natural ventilation (to the extent possible, they should be placed as far apart as

possible).

- Inspection hatch(es) of at least 40 x 50cm for service access (at least to the motors). Riho recommends

that an inspection hatch should be placed near the overflow opening.

- Hot and cold water supply.

- Water drain

- Electrical connection, one or two groups of 230V/50Hz 16Amp with earth leakage switch, dependent

on your options (option heater). Also see chapter 1.5.6

- Potential difference equalisation 6 mm² earth connection to whirlpool frame.

- Splash-proof rim around the whirlpool.

The installer should pay special attention to the following points before installing the bath:

- Check the bath and the whirlpool for possible defects before installation. No dismantling costs will be

paid in the case of defects found after installation. After installation, Riho can only give a guarantee on

hidden defects.

- When transporting and installing the bath, do not hold it by the pipes, hoses and jets.

- Check the whirlpool for leaks before installation.

- The whirlpool bath must be clear of the wall, so that unavoidable vibrations caused by the motor are not

transferred to it. The use of bath insulation tape between the bath rim and walls is recommended this will

reduce the noise level.

- If plastic panels are installed, pay attention to the height of the panel with respect to the bottom edge of

the bath. The panel should be at least 5mm from the floor, for ventilation purposes.

In case of doubt, consult a plumbing specialist.

1.2 Whirlpool installation

All Riho Whirlpool baths are made of acrylic (see description: acrylic baths) and equipped with a Whirlpool bath as per

customer's choice.

Please refer to the Riho price lists for details of all options.

1.3 Delivery:

Generally, all whirlpool systems are fully installed, functionally tested and packed.

All Whirlpool baths are supplied with a flexible PU drain-overflow, which in some cases is not fitted when delivered.

! ATTENTION! Before installation, check the bath for damage, as well as material and/or manufacturing defects. For

this remove, the cardboard packaging. In order to prevent damage during installation, allow the foil to remain as long

as possible and remove it only at the last moment. After installation, Riho can only give a guarantee on hidden material

defects. Check the foil for scratches and damage if any. If these are present, check the bath itself to see whether it is

damaged. For this, remove as little foil as necessary in order to protect the bath as properly as possible during

installation. In case of doubt, consult a plumbing specialist.

WARNING; make sure chrome parts don't come into contact with materials or water used to remove building materials,

such as mortar, grout or tile adhesive because of possible chemical components in the composition which can damage

the chrome surface.

THE MANUFACTURER REFUSES TO ACCEPT ANY LIABILITY IN THE FOLLOWING CASES:

- the national guidelines and standards that apply to earthing, potential difference equalising and electrical

installations in the bathroom are not adhered to.

- the description contained in the national laws and standards that apply to safety in bathrooms are not

adhered to.

- the instructions described in this manual are not adhered to.

Parts are dismantled after inspection in the factory to facilitate transport and to enable it to be carried into the

room in which it is to be installed. It is advisable to check all the components of the bath before installation.

Any damage claimed after installation will not be covered under the guarantee.

Diagram fig. 1 Safety distances.

1.0 Installation of Riho Whirlpools

The Whirlpool baths are fully in conformity with the applicable EN and national guidelines.

The installation must be fitted by a recognised installer.

The assembly and installation of the whirlpool must be done in accordance with the instructions described

in this manual.

The installer will be responsible to check that the civil, electrical and water-related pre-installation work

is done properly.

1.1 Safety regulations for bathrooms.

Electrical sockets, lamps, switches and/or other electrical equipment should be installed outside the danger zones

indicated in the national guidelines and standards. Above all, the regulations prohibit the presence of any electrical

installation within 60 cm around the bath, and less than 225 cm above it (see Fig.1). The switch and other electrical

devices should be installed so as to be inaccessible to the person using the whirlpool.

-31--30-

40c

Zone

Zo e

ne 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Riho Whirlpool Electronic LCD Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Riho Whirlpool Electronic LCD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info