Bedienungsanleitung Roadstar HIF-3650UMP (Seite 5 von 12) (Deutsch, Englisch)

592089

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

EnglishEnglish

NORMAL DISC PLAY

• Open the disc compartment by lift on the CD OPEN right corner and load a CD.

• Close the disc compartment.

• Press the PLAY / PAUSE button (7). The disc play will begin from the start of the first

track of the disc.

• A particular track can be selected using either the CD Skip buttons (8,24). If this is done

before pressing the PLAY / PAUSE (7) button, disc play will start with the selected track

when the PLAY / PAUSE button is pressed.

• At the end of the disc, the unit will switch to stop mode.

Notes: If the disc is deeply scratched, or too dirty, disc play may not start.

If on improperly centred disc is played, noise can be heard in the mechanism. The

use of such discs should be avoided.

IMPORTANT INFORMATION

This compact disc player has built-in error compensation circuits to correct for minor defects

in a disc.

There are limits, however, to the amount of correction available.

In some cases, the CD / MP3 player may skip some tracks on a disc during disc play. This

problem may be cause by defects (such as scratches) in the disc being played, which are

too large for the error compensation circuits to handle. If you encounter this problem, check

the CD player’s operation as follows, before having the unit serviced:

Play a new disc. If the CD player operates normally, the skipping problem is probably due to

a defective disc.

TO STOP A CD PART WAY THROUGH

• Press the Stop button (7). Disc play will stop and the display will show the total number of

tracks for the CD.

• To temporarily stop disc play (pause mode), press the Play / Pause button. Disc play will

pause at the current play position. The Play/Pause indicator will flash.

• To resume disc play, press the Play/Pause (7) button again.

TRACK SKIP (CD / USB)

STARTING DISC PLAY FROM THE BEGINNING OFA PARTICULAR TRACK

• Press the Forward or Reverse Skip / Search Track button (8,9) to select the desired track.

The number of the selected track will be shown on the display. Press the Play/Pause button

to start play.

TO SKIP TO THE NEXT TRACK

• Press the Forward Skip / Search Track button (8) once. Play will resume at the beginning

of the next track.

7 8

The player will skip ahead to the next track each time the Forward Skip / Search Track

button is pressed. Continuously pressing the Forward Skip / Search Track button makes

the player skip ahead through the track by track. Once the beginning of the last track is

reached the player will not advance any further.

TO SKIP BACK TO THE PREVIOUS TRACK (CD / USB)

• Press the Reverse Skip / Search Track button (8/9). If this button is pressed in the middle of

a track, the player will skip back to the beginning of that track. To make it skip back to the

previous track press the Reverse Skip / Search Track button (9) twice.

Continuously pressing the Reverse Skip / Search Track button makes the player skip

back through the disc track by track. Once the beginning of the first track is reached, the

player will not go back any further.

Notes: Tracks can be selected even when the Compact Disc compartment is open. However

if a track number is selected that is not present on the CD, disc play will start from

the beginning of the last track.

PROGRAMMED PLAYBACK (CD / USB)

It is not possible to enter programs during CD/USB play. Press the Stop button (7) first, then follow

the instructions below.

Press the PROGRAM button (13). “P01” and the PROGRAM indicator will light up.

Press the Forward and Reverse Skip Track buttons (8/9) to select the track to be stored in

position1.

Press the PROGRAM button (13). The first program selection is now stored in the program

memory 1.

Select the next track to be programmed using the Forward and Reverse Skip Track (8/9)

buttons.

Press the PROGRAM button (13) to store this track.

Continue entering tracks in this way until all the desired tracks are stored (up to a limit of20).

When the PROGRAM button (13) is pressed to store the 20th track, the display will return to

the 1st program location. Press the PROGRAM button (13) to step through the program

locations.

Listening to Programmed Tracks (CD / USB)

Press the Play Pause button (7). Disc play will start at the beginning of the first programmed track.

To Clear The Program Memory (CD / USB)

If the disc is playing, press the Stop button (25) to stop the disc.

Switch the Function (11) selector to a different position (RADIO/AUX) to clear the Program.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roadstar HIF-3650UMP Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info