Bedienungsanleitung Rockford Fosgate P1000X1BD (Seite 3 von 12) (Englisch)

602268

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Design Features

Power/Protect LED

Power LED illuminates blue when the unit is turned on. Protect

LED illuminates yellow if a short circuit or to low of an impedance

is detected at the speaker connections. Thermal LED illuminates

red when ampliﬁer overheats. The ampliﬁer will automatically shut

down if this occurs.

Output Clip Indicator Chart

Reference chart for the output clip in-

dicator LED illumination color during

input level setup.

Speaker Terminals

The Speaker Terminals are nickel-plated

captive c-clamp wire connectors (+ and -)

will accommodate 8 AWG.

RCA Input/Pass-Thru

The RCA inputs are capable of accepting signal from either high-level(speaker) to low-

level(RCA). When utilizing high-level for input signal the auto turn-on feature is active.

The pass-thru RCA’s are passive, including full input signal range and auto turn-on

functionality when active.

Subwoofer Input

Setting this switch to the “On” position, utilizes the

“Sub” inputs. (P1000X5)

Centering Indicators

Indicators are located on the bottom side of the

ampliﬁer.

Output Clip Indicator

The output clip indicator works in conjunction with

the input level knob, illuminating to appropriate

color depending on the audio content used for the

setup.

Intput Clip Indicator

The input clip indicator works in con-

junction with the audio source volume

knob, illuminating red when audio

source reaches it’s clipping point.

Input Level Knob

The input level control is used to match

the output of the audio source.

Design Features

Punch EQ

A Gyrator based Punch EQ that eliminates frequency

shift with boost. This works along with the crossover

switch on the ampliﬁer.

Power/REM Terminals

The power and ground will accommodate 4 AWG,

while the remote will accommodate 12 AWG.(The

REM terminal is used to remotely turn-on and

turn-off the ampliﬁer when +12V DC is applied.)

2/4 Channel Switch

Setting this switch to the 2CH. position, switches the

inputs to a 2-channel mode, allowing connection to

only the front inputs with a 4-channel output. (P400X4,

P600X4, P1000X5)

Crossover Switch

Selectable switch for High-Pass (HP) or

All Pass (AP) or Low-Pass (LP)

Variable Crossover

Is a built-in 12dB/octave Butterworth ﬁlter with

a crossover point variable from 50Hz to 250Hz.

illus.-1.1

Remote Punch Level Control - In/Out

Remotely control the output level of the ampliﬁer. The

PLC-OUT is used to daisy-chain additional ampliﬁers

controlled by a single remote.

Infrasonic Filter

A ﬁxed 28Hz 12dB/octave ﬁlter designed to prevent

frequencies below the audio range from being applied

to the subwoofer from the ampliﬁer. Consequently

improving subwoofer performance and power han-

dling, particularly in vented enclosures. (P500X1BD,

P10001BD, P1000X5)

Remote Punch Level Switch

When activated, this allows the use of a optional re-

mote Punch Level Controller. (P500X1BD, P10001BD,

P1000X5)

INPUT CLIP

REAR SUBFRONT

RIGHT

LEFT

RIGHT

LEFT

B+

REM GND

REMOTE

PUNCH LEVEL

PLC-OUTPLC-IN

FRONT REAR

RIGHTLEFT

BRIDGED

RIGHTLEFT

BRIDGED

SUB

SPEAKERS

INPUT

2CH. - 4CH.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rockford Fosgate P1000X1BD Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info