602257
8
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
8
OPERATION
ADJUSTING CROSSOVER FREQUENCY
The crossover is set to Low Pass only, enabling frequencies below the cut-off point to pass,
adjustable between 35-250Hz.
Turn the crossover adjustment knob to the minimum setting.With the system playing, turn
the crossover adjustment knob up slowly until the desired crossover point is achieved.
VARIABLE HIGH LEVEL ADJUSTMENT
For a high level(speaker) input application the High/Low Level Switch needs to set to
High.
With the switch set to High, utilizing a 6V DC(Direct Current) offset voltage, the
Punch Boosted Rail amplifier can be turned on/off allowing the REM to be used as an
output to turn on/off an amplifier or other accessory.
The variable high level adjustment can be used to delay the turn on eliminating induced noise,
turn on/off pop.
ADJUSTING GAIN
To adjust the gain setting, turn the amplifier gains all the way down (counter-clockwise).Turn the source unit
volume up until distortion is audible and then turn it down a bit until the distortion is inaudible.This will be about
all the way up on most source units. Next, increase the amplifier gain setting until adequate volume is achieved.
NOTE:Best signal to noise and dynamic range are realized with the gain at minimum. Most users find adequate
gain and volume is achieved at about halfway in the adjustment range.
CAUTION:Avoid setting the amplifier gain very high as noise and distortion will increase
significantly.
NOTE:For a more in depth setting procedure, contact Rockford Technical Support.
REMOTE PUNCH EQ (Option)
NOTE: Previous (prior to 2007) Punch Bass and Para-
Punch remotes will not work with these amplifiers.
NOTE:Use the instructions that came with the remote for
a variety of mountings that fit your preference.
Quick Install
1. Using the screws supplied, install the mounting clip.
2. Slip the remote onto the mounting clip until it snaps
into place.
3. Route and connect the cable to the remote and
amplifier.
Operation
4. Variable bass boost centered at 45Hz.
CAUTION: Overexcursion and subsequent damage may occur at high levels of boost.
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Rockford Fosgate PBR500X1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info