Bedienungsanleitung Rockford Fosgate PMX-0 (Seite 5 von 16) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

662896

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Installation / Mounting / Operation

Basic Operation

TURNING THE UNIT ON / OFF

Press the POWER button to turn the unit ON or OFF

ADJUSTING THE VOLUME

Rotate encoder knob left or right to the desired volume level. You will

hear a beep when the VOLUME has reached it’s maximum volume level.

ADJUSTING THE SUBWOOFER OUTPUT

Press the SUB + or SUB- buttons to adjust the output level. You will

hear a beep with the settings have reached their minimum and maximum

setting.

SELECTING A SOURCE TO PLAY

Press the SRC button to scroll through and select the audio source of

your choice. An audible notiﬁcation will let you know what source is

selected (BLUETOOTH MODE>AUXILLARY MODE).

USB Operation

The USB port on the back of the device is for ﬁrmware updates and

charging devices only. Using it as an audio source will not work.

AUX Operation

After your device is plugged into the source unit, this feature allows you

to play music from your device. To select the AUX source, press the SRC

button until you hear “AUXILIARY MODE” over the speakers. You will use

your plugged in device to control song/track selection, PLAY/PAUSE and

track skip FWD/REV.

Bluetooth

Operation

To pair your device to the source unit, you will need to go to your

Bluetooth settings on your device and select “Rockford PMX0”.

After the initial pairing of your device, the volume will be set at 25%

volume. You will need to set the Volume on your device to 100% for

maximum sound.

Once your device is paired to the source unit, this feature allows you to

control playback from your device directly from the unit. To select the

BLUETOOTH source option on the source unit, simply press the SRC

button until you hear “BLUETOOTH MODE”.

To play or pause a song, short press the PLAY/PAUSE button.

To skip a track forward, short press the FWD button. To skip a track

backwards, short press the REV button.

Contents

Installation Considerations

The following is a basic list of tools needed for installation:

This section focuses on some of the vehicle considerations for installing

your new source unit. Pre-planning your system layout and best wiring

routes will save installation time. When deciding on the layout of your

new system, be sure that each component will be easily accessible for

making adjustments.

If you feel unsure about installing this system yourself, have it installed

by a qualiﬁed Rockford Audio technician.

Before installation, disconnect the battery negative (-) terminal to prevent

damage to the unit, ﬁre and/or possible injury.

Before beginning any installation, follow these simple rules:

1. Be sure to carefully read and understand the instructions before

attempting to install the unit.

2. For safety, disconnect the negative lead from the battery prior to

beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting

your unit in place.

4. Route all of the RCA cables close together and away from any high

current wires.

5. Use high quality connectors for a reliable installation and to minimize

signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel

lines, brake or hydraulic lines, vacuum lines or electrical wiring when

working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the

vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber

or plastic grommets to protect any wires routed through metal,

especially the ﬁrewall.

9. ALWAYS protect the battery and electrical system from damage with

proper fusing. Install the appropriate fuse holder and fuse on the

+12V power wire within 18” (45.7 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from

the metal to ensure a good, clean ground connection. Grounding

connections should be as short as possible and always be connected

to metal that is welded to the main body, or chassis, of the vehicle.

Seatbelt bolts should never be used for connecting to ground.

• Volt/Ohm meter

• Wire strippers

• Wire crimpers

• Wire cutters

• #2 Phillips screwdriver

• Battery post wrench

• Hand held drill w/ assorted

bits

• Heat shrink tubing

• Soldering iron

• Solder

• Heat gun

• 7mm wrench

• Source Unit

• U Bracket & Nuts

• Installation & Operation

Manual

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rockford Fosgate PMX-0 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info