167797
4
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
T500-1bd
CP
T1500-1bd CP
T1000-1bd CP
45678
9 10 12
11 13 14
4578
96 10 12
961012
11 13 14
4 5 7 8 11 13 14
1. Power LED (Top of unit - Not Shown) This Blue LED illuminates when the unit is turned on.
2. Thermal LED (Top of unit - Not Shown) This Red LED illuminates if the amplifier internal components
become too hot and engage the thermal protection.The amplifier will shut down to cool if this occurs.
3. Protect LED (Top of unit - Not Shown) This Yellow LED illuminates if a short circuit or too low of an
impedance is detected at the speaker connections.The amplifier will automatically shut down if this occurs.
4. Cast Aluminum Heatsink The cast aluminum heatsink of the Power amplifier dissipates heat generated by
the amplifier's circuitry.
5. Speaker Terminals The heavy duty,nickel-plated clamp wire connectors (
+
and -) will accept wire sizes from
8 AWG to 18 AWG.
6. Remote Punch EQ (Optional Controller) The Remote Punch EQ connection is made with a RJ-45 cable
and can be installed in a variety of ways for easy control access.The control is used to boost low and/or high
frequency information to overcome road noise.The remote overrides the Punch EQ on the amplifier when
connected.
NOTE: Previous (prior to 2007) Punch Bass and Para-Punch remotes will not work with these amplifiers.
7.
Punch EQ This control is a narrow band adjustment variable from 0dB to +18dB @ 45Hz with a Gyrator
based Punch EQ that eliminates frequency shift with boost.
8.
Infrasonic Filter A 28Hz High Pass filter designed to prevent frequencies below the audio range from being
applied to the subwoofer from the amplifier. Consequently improving subwoofer performance and power
handling,particularly in vented enclosures.
9.
Variable Crossover – Is a built-in 24dB/octave Butterworth filter with a crossover point variable from 35Hz to
250Hz.The crossover is set to Low-Pass (LP).
10.
Gain Control The input gain control is preset to match the output of most source units.It can be adjusted to
match output levels from a variety of source units.
11.
RCA Pass-Thru Jacks This Pass-Thru provides a convenient source for daisy-chaining an additional amplifier
without running an extra set of RCA cables from the front of the vehicle to the rear amplifier location.
12. RCA Input Jacks The industry standard RCA jacks provide an easy connection for signal level input.They are
nickel-plated to resist the signal degradation caused by corrosion.
13. REM
T
erminal
The hea
vy duty
,
nickel-plated captive c-clamp wire connector will accept wire sizes from
12
A
WG to 24
A
WG.This terminal is used to remotely turn-on and turn-off the amplifier when +12V DC is
a
pplied.
14.
Power Terminals The power and ground are nickel-plated captive c-clamp wire connectors and will
accommodate up to 4 AWG wire.
4
DESIGN FEATURES
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Rockford Fosgate t 1001 bd wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info