Bedienungsanleitung Rockford Fosgate t1000 4 (Seite 4 von 64) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

168821

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

DESIGN FEATURES

678 8

10 11 1110

12 12

15 16

1. Power LED (Top of unit) – This Blue LED illuminates when the unit is turned on.

2. Thermal LED (Top of unit) – This Red LED illuminates if the amplifier’s internal components become

too hot and engage the thermal protection.The amplifier will shut down to cool if this occurs.

3. Protect LED (Top of unit) – This Yellow LED illuminates if a short circuit or too low of an impedance

is detected at the speaker connections.The amplifier will automatically shut down if this occurs.

Output Display (Top of unit) – These LEDs simulate VU meters to display the real-time front and

rear output of the amplifier from - 00 (infinity) to +2dB. During normal operation the indicator should

not reach +2dB, as this indicates clipping.

Cast Aluminum Heatsink – The cast aluminum heatsink of the Power amplifier dissipates heat

generated by the amplifier's circuitry.

6. Speaker Terminals – The heavy duty,nickel-plated wire connectors (

and -) will accept wire sizes from

8 AWG to 16 AWG.

7. Remote Punch EQ (Optional Controller) – The Remote Punch EQ connection is made with a RJ-45

cable and can be installed in a variety of ways for easy control access.The control is used to boost low

and/or high frequency information to overcome road noise.The remote overrides the Punch EQ rear

channel control on the amplifier when connected.

NOTE:Previous (prior to 2007) Punch Bass and Para-Punch remotes will not work with these amplifiers.

8. RCA Input Jacks – These pro-audio panel mount RCA jacks provide an easy connection for signal level

input.They are nickel-plated to resist the signal degradation caused by corrosion.Their design reduces the

stress created to internal boards when RCA cables are connected or disconnected.

9. Punch EQ – A Gyrator based Punch EQ that eliminates frequency shift with boost.This works along

with the crossover switch on the amplifier.When set to Low-Pass (LP) operation, this is a variable Bass

Boost. When set to High-Pass (HP) operation, this is a variable Mid-Bass and Treble Boost. When set to

All Pass (AP) operation, both the Bass and Treble frequencies are boosted.

10. Crossover Switch – Selectable switch for High-Pass (HP),All Pass (AP),or Low-Pass (LP) operation.

11. Variable Crossover – Is a built-in 24dB/octave Butterworth filter with a crossover point variable

from 50Hz to 500Hz.

12.

Gain Control – The input gain control is preset to match the output of most source units. It can be

adjusted to match output levels from a variety of source units.

13.

2/4 Channel Switch – Setting this s

witch to the 2CH. position, switches the inputs to a 2-channel

mode

, allowing connection to only the front inputs with a 4-channel output.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rockford Fosgate t1000 4 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info