Bedienungsanleitung Roland Blues Cube Hot (Seite 9 von 13) (Englisch)

709206

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Panel Descriptions

10 PHONES jack

Connect headphones here. You can obtain powerful guitar sounds

just as if you were playing through the speaker. To adjust the

volume, use the [VOLUME] knob along with the [MASTER] knob.

* If a plug is inserted in this jack, no sound will be output from

the Blues Cube’s own speaker. This is convenient if you don’t

want loud sound to be produced from the speaker, such as

when you’re practicing at night.

11 LINE OUT jack

Connect this to your PA system or recorder. You can obtain powerful

guitar amp sound just as if you were playing through the speaker.

Recorder, etc.

You can use this in conjunction with an external PA system, or to

record your performance via direct line while monitoring the sound

from the Blues Cube’s speaker.

Adjust the output level using the [VOLUME] knob.

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

12 REC OUT

port

You can use a commercially available USB 2.0 cable to record the

sound of the Blues Cube into your computer.

You must install the USB driver when connecting the unit to

your computer.

Download the USB driver from the Roland website. For details, refer

to Readme.htm which is included in the download.

http://www.roland.com/support/

Turning the Power On/O

* Once everything is properly connected (p. 6), be sure to

follow the procedure below to turn on their power. If you turn

on equipment in the wrong order, you risk causing malfunction

or equipment failure.

1. Make sure that the Blues Cube’s [MASTER] knob and the

volume of the devices connected to the Blues Cube are set

to 0.

* Before connecting your instrument to the Blues Cube’s INPUT

jack, set the [MASTER] knob to the minimum setting (far left).

2. Turn on the Blues Cube.

* Before turning the unit on/o, always be sure to

turn the volume down. Even with the volume

turned down, you might hear some sound when

switching the unit on/o. However, this is normal

and does not indicate a malfunction.

* This unit is equipped with a protection circuit. A

brief interval (a few seconds) after turning the

unit on is required before it will operate normally.

3. Turn on the power of the devices connected to the LINE

OUT jack, PHONES jack, and REC OUT

port.

4. Adjust the volume levels for the devices.

Before switching o the power, lower the volume on each of the

devices in your system and then TURN OFF the devices in the

reverse order to which they were switched on.

* If you need to turn o the power completely, rst turn o the

unit, then unplug the power cord from the power outlet. Refer

to “To completely turn o power to the unit, pull out the plug

from the outlet” (p. 2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland Blues Cube Hot Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland Blues Cube Hot

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info